Subject: Question on Turbo compounding turbo compressor drive coupling to TC drive]
From: Rotary Engine
Date: 12/6/2006, 9:26 PM
To: AARotary Engine




     >>> Giffen Marr wrote:
     >>>> Paul
     >>>>
     >>>> Am I to understand that the TC Drive is to be driven by a
    shaft from the
     >>>> Turbo compressor? If so, aren't shaft rotational speeds of 60k
    to 80k
     >>>> going
     >>>> to present a problem?
     >>>>
     >>>> Giff Marr
     >>>> LIV-P/20B 45%
     >>>>
     >>>>
     >>>
     >>> What problems did you have in mind? This is what I tink I am going
     >>> to use in the 1/2 inch size.
     >>>
     >>
     >> Paul, you are joking right?
     >> Mark W.
     >>
     >>
     >> No Not joking. What problems do you see?
     >> --
     >> Paul Lamar ...No rotor no motor.
     >
     > Lack of balance, lack of strength, a horrible failure mode with
    an easier
     > released projectile.
     >
     > At 80K RPM, any imbalance will be be exciting it with 480KHz (two
    per rev).
     > At this frequency, you will at least wear out the metal to metal
    contact
     > points in the universal (although as Reeves says, you will be
    very unlikely
     > to get up to this RPM.). Turbines normally use some sort of splined
     > coupling, a rigid coupling with a floating oil damped bearing, or
    driving
     > lubs these days.
     >
     > Be really careful testing this Paul.
     >
     > Mark
     >
     >
     > Thanks Mark. I think I will test both the bellows type as Reeve
     > suggested and this type if the off the shelf versions are
     > reasonable well made with tight tolerances. The drawback to
     > the bellows type is a somewhat larger OD for a given torque rating.
     > The second web site Reeve mentioned offer balanced bellows
     > type.
     >
     >
    http://www.rw-america.com/PDF-couplings-line-shafts/MK_miniature-bellows-cou
     > plings.pdf
     >
     > BTW what are "lubs" ?
     >
     > Alignment is near perfect when the engine is cool.
     > I am concerned with slight mis-alignment due to temp difference
     > in the various parts as the engine and turbo charger
     > warm up.
     >
     > Paul Lamar ...No rotor no motor.
     >
     > Paul,
     > Have you found a suitable coupling or method of connecting the TC
    drive
     > to the turbo compressor shaft ?
     > Will any extra weight of a coupling or a modified nut which will
    form one
     > Side of the coupling, or any side load on the compressor end of
    the shaft
     > Due to heat or expansion misalignment no matter how small, have
    an affect
     > on the turbocharger bearings.
     > As the turbo compressor and turbine rotors are both overhung and the
     > bearings
     > are between them and close together will the extra load affect
    this rotating
     > mass causing the rotors and shaft assembly to wobble.
     > Geoff
     > Cheshire
     > England
     >
     > I don't really know. I hope not. The torque is real low
     > so I am still leaning towards a teflon lined SS hose
     > with crimp fittings to keep the diameter to a minimum.
     > The shaft is very short at only about 1.5 inches long
     > and about the dia. of a pencil.
     >
     > Paul Lamar ...No rotor no motor.


    Paul

    Here is a good Motor Trend article about the BorgWarner VGT. If I
    can find
    someone to search for a good used one found on the smaller Detroit and
    Cummins diesels I can solve the last parts challenge to get the
    turbo compound test engine under construction. The challenge may be
    getting
    one small enough though.

    http://tinyurl.com/y7tsg7


    DougFir

    That is like a variable A/R. One can tune the turbine
    for max HP output at any RPM. That will put the turbo
    compound passenger car rotary over the technical hump.
    It will make it easier to set up an aircraft turbo
    charger as well.

    Paul Lamar ...No rotor no motor.


    Paul and Doug,

    Variable A/R is exactly what it is. For cars the vanes automatically
    adjust to rpm, but for an airplane engine, we need them to adjust to
    baro pressure change with altitude..

    So we hook up a bellows aneroid to the actuator so it moves the
    vanes as we go higher.

    Doug, you mentioned that this could do away with the CVT drive and
    this is correct. You would need to dial in the system, but once you
    have the size and geometry figured out, you don't need the variable
    belt drive. At least in theory.


    Regards,

    Gordon.



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.