Subject: Kinsler Nozzles mechanical pump fuel injection.
From: Rotary Engine
Date: 12/7/2006, 9:23 PM
To: AARotary Engine


     > Gordon
     >
     > Yep, Parker is another good company. That should work.
     >
     > Doug
     >
     > What do you guys have against this idea? What is wrong
     > with it?
     >
     > Paul Lamar


    Hi Paul,
    there is nothing wrong with it per se : but using your reasoning...

    What do you have against the Parker valve? What feature is missing that
    we need? What is wrong with it?

    For: It is well made, it has the known flow characteristics ,easy
    to mount, easy to operate, vernier adjustment, and readily
    available.

    Using the Parker valve makes the Slide throttle a lot simpler, in that
    the leaning feature is remote from the moving slide.
    And if you must mess with the needle on your lathe/ mill, then you can
    simply dismantle the valve for easy access.

    Against: Its mode of operation is not like that on a "Cessna spam can"
    ???

    Dave McC

    Where do I begin?

    The long needle valve is also remote from the moving slide.
    However you want to keep it as close as possible so
    vapor is not made in the fuel line from the valve
    to the slide throttle by engine heat.

    Anything that you have to twist remotely means
    you need a torsionally stiff shaft. That rules out the stock
    off the shelf leaning cable with vernier as it's shaft is only about
    .1 inches in diameter. It must be that small so the valve
    can be out of axial and lateral alignment with the twisting
    knob three feet away on the instrument panel. If there is any
    wind up in the shaft it makes fine adjustment difficult. It also
    must accommodate movement by the engine in it rubber mounts. Sure
    a 1/2 inch aluminum tube could be used if you mounted it on the
    firewall. Now you have at least two couplings to deal with
    and a new knob. Mounting the whole valve on the instrument
    panel means you have a longer fuel line to the slide throttle
    with more opportunity for fuel vapor accumulation.

    The second major problem is it takes too much time to open
    fully or close fully. That is a major feature on the long needle
    valve. You need to open the valve completely to prime
    the engine for starting and close it quickly for shutting off
    the engine.

    Third, the long needle valves position is obvious from
    a glance at the knob sticking out of the instrument panel.
    No need to read a small rotating scale.

    Forth, pilots don't need to be retrained. Anybody flying a
    Cessna "spam can" (I represent that crack :)) will know exactly
    how and why it is used.

    Paul Lamar ...No rotor no motor.


    Paul,

    I'll start with the disadvantages of your needle valve:

    1. Its action is in the wrong direction, so if you want to pull out
    for leaning you have to mount a lever that will reverse the needle
    travel. You were just railing against levers as prone to slop...

    2. Those O-rings will leak if you try to run any more than a few
    pounds of pressure, so the valve is not usable on the constant flow
    injection system. It would probably work ok with the slide throttle
    carb.

    Now the stuff you mentioned against the Parker valve:

    1. Yes, it is a different "interface" than the standard pull out for
    leaning mixture control. Okay, but what is the alternative? EFI with
    no mixture control at all? Or a little knob to control an
    after market EFI system? Compared to this, I'll take the manual twist
    knob.

    2. There can be no windup and hence no slop with an aluminum tube
    extension like Dave suggested. All you add is an aluminum tube. You
    use the same knob that comes with the valve.

    Regards,

    Gordon.

---------------------------------------------

    I am only concerned with the low pressure 2 psi fuel system.
    You high pressure mechanical system guys are on your own :).
    Too expensive for me. Requires a high pressure pump.

    Colin Smith came up with a simple variation that changes the direction.
    I like his idea better than mine as it has the potential for
    a more positive shut off feature. I am working on a 3D.

    Paul Lamar ...No rotor no motor.

 -----------------------------

    Paul,

    I agree your slide throttle carb is an attractive way to go at very
    low cost. Just a little elbow grease to make one. (Okay, maybe more
    than a little...)

    But you still need a mechanical pump even at low pressure, unless
    you have high wing tanks. Maybe the stock diaphragm pump could work,
    but those diaphragm pumps are more prone to vapor lock. (I don't
    want to open that debate again; I know you can keep the fuel lines
    cool with a blast tube, routing away from hot spots etc...)

    If you decide to use a positive displacement mechanical pump like
    the Kinsler pump, are already half way to spending what it costs for
    the full mechanical injection. The pump is the biggest expense in
    the whole constant flow system.

    The only other things you would need are the barrel valve and two
    nozzles (for a P-port; more for more runners). Here is a Kinsler
    single-port barrel valve. You can run that to an AN Tee
    fitting that will split a fuel line to each runner.

    You would have to weld a nozzle boss on each runner, and make up
    some AN fuel lines and fittings. You would use the Parker valve and
    panel adjustable twist knob for leaning.

    Throttle would be with your slide throttle. The whole thing would
    probably cost less than an Ellison carb. Because of the higher
    pressure it would be much less susceptible to vapor lock than an
    Ellison. It also would not need carb heat.

    So compared to an Ellison carb it's a great deal. If you want to use
    a turbo or supercharger, it is a perfect way to go. Even for a
    normally aspirated engine it's a great way to go.

    Compared to EFI it's an even better deal. Even with stock EFI you
    need at least two high pressure electric pumps. They aren't cheap.
    And then what about an after market controller, like Tracy's unit or
    some others. These cost about $1,000 I believe.

    Then you've got your injectors, etc.

    And after all that money spent you're 100 percent dependent on
    electrical just to keep your engine running. If your juice stops
    flowing, you are coming down. This does not sound like a good deal
    to me.

    So while the constant flow injection is a little more expensive than
    the slide throttle carb, it is still a very good option when
    everything is considered.


    Regards,

    Gordon.

I think you are going to run into trouble if you try to limit the output
of a positive displacement mechanical pump with a needle valve. In car racing
they could care less about leaning for cruise. In aircraft we need full power
for take off and super lean for cruise. In car racing they need full power....
PERIOD :) Race cars also don't idle. Do you have any 800 HP sprint car racing
up there?

Doug, next time you come to my house I'll take you to the sprint
car races and into the pits after the race so you can see some of
these systems. I can hear them from here every Saturday night :)

Fuel delivery in these race car systems is only a function of RPM.
You can not get more fuel out of a positive displacement pump if you
lower the pressure on the output side. If you restrict the output
with a needle valve no telling what happens. It will probably overheat
the pump and the fuel.

In mine, Ellison, Aerocarb, Revmaster, etc., etc.,  fuel delivery is tied to
throttle opening and intake manifold vacuum.

The diaphragm pump won't work as they are designed to work off a
cam shaft.  A mechanical pump driven off the e-shaft will work
with my system as well. All it need do is fill a small header tank equipped
with a stand pipe. If it pumps too much fuel it just goes back to
the fuel tank through the stand pipe. No back pressure to speak of
on a positive displacement mechanical pump.


Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.