Subject: Kinsler Nozzles mechanical pump fuel injection. (Turbonormalized)
From: Rotary Engine
Date: 12/9/2006, 10:37 AM
To: AARotary Engine

   Good luck on the turbo charging. A lot of people have
   blown up a lot of Mazda rotaries by screwing up the turbo charging.
   Mazda thought the 2nd gen Turbo II RX7 needed an inter cooler with
   only 5 psi boost. They put a detonation sensor on there as well.
   150 F is getting in the detonation range.

   My RX2 had an electric pump.

   Paul Lamar


   Paul,

   Five psi boost at sea level will make hotter air than 8 psi at
   20,000 feet where air is much colder.

   Also the 150 F temp is before evaporative cooling at the port. This
   will drop the temp to about 110 F. This is downright chilly. Even
   150 is fine. I've never heard of 150 causing detonation.

   Btw, the new Garrett catalog has a turbo that should work just about
   right for a turbonormalized 2-rotor.

   Use the compressor from the GT3782 and the turbine from the GT4088.
   Here are the catalog pages for both.

   Notice the large 1.34 trim on the larger one? That's why the turbine
   flow keeps building until 2.5 pressure ratio. This is just what we
   need at 20,000 feet, where we need just under 2.5 to get sea level MAP.

   So that curve will give us increasing boost all the way up to our
   service ceiling. The smaller one would work too, but its curve
   flattens out at 2 to 1 compression. Not ideal. It would work well to
   about 15,000 feet.

   The compressor on the smaller one is just right though.

   If I were building a turbonormalized 2-rotor, this is what I would
   use. You wouldn't even need a wastegate. No way you are going to
   spin that big turbine up into trouble territory unless you go much
   over FL200.


   Regards,

   Gordon.

   Sounds like an extensive R&D program due to the total
   lack of info on the HP available from specific turbines and the HP
   consumption of specific compressors. Until the turbo charger
   guys wake up and start publishing dyno HP numbers it will
   remain difficult to come up with a simple design process.
   Apparently a lot of first hand experience counts for a lot.

   I did a bit of this R&D with Garrett back in 1980.

   "The Effects of Turbocharger Design and Installation on
   Gasoline Vehicle Transient Response.
   David Elpern. Garrett Automotive Products Co.
   SAE 821149 Use of the Lamar Instrument test
   equipment to develop turbocharger design."

   Even Borg Warner teamed up with Porsche to develop an application.
   So far nobody has been able to hit the happy combination out of the
   gate without some trial an error. Then you have the extra exhaust
   heat of a rotary to contend with. We really know next to nothing
   about the rotary exhaust. We do know there is a lot of kinetic
   energy in there due to the ear piercing noise they make and we
   do know they run 1700 to 1800 F. That is about it.

   Your talking big bucks for the R&D. The number of people interested
   in this are few and far between. It will be years before
   many high buck people are going to install a rotary. Years
   before the rotary will be recognized as worth the extra trouble
   by the mainstream aviation community. Much easier to buy an
   aircraft engine off the shelf if money is not that important.
   After all an aircraft engine will last 20 years at 100 hours
   per year. In the mean time more and more guys looking to
   save a buck will be installing rotaries. We owe a lot to
   the few guys that have persevered so far on the turbo chargers
   like Tom Parkes, Dave Leonard and John Slade.

   The turbo compound rotary may change the dynamics but only if
   the fuel price doubles or aircraft range becomes more of an issue.

   BTW I like the Borg Warner variable A/R. Much easier
   to match and they have been cheaper in the past
   than Garrett.

   --
   Paul Lamar ...No rotor no motor.

   Paul,

   Garrett has been making variable A/R turbos for diesel engine
   pickups from Ford and GM -- the PowerStroke and Duramax engines
   -- for some time. You could probably find one at your local boneyard
   without much difficulty. Btw, Gerrett calls them AVNT, which stands
   for Advanced Variable Nozzle Turbine.

   These would certainly make R & D go more quickly. With the
   adjustable vanes you can dial in just the curve that you need.

   Other than that I agree with you on the R & D point. That's why I
   said it would be good to instrument the exhaust and graph the data
   like the CAFE guys have done. This could be replicated wihtout too
   much work and expense using simple pressure transducers and whipping
   up a circuit board to digitze the analog signals from the sensors.

   Still, I think with just basic calculations we can come pretty
   close. If I were building one I would put on a manually controlled
   wastegate first and do some flight testing to see how the system
   works. After that a simple fixed wastegate or wastegate linked to
   throttle linkage could be substituted once you are sure of the
   dynamics. Maybe even no wastegate at all.

   Sure it would take a little effort with the flight tests but it
   would be well worth it.

   The route that you are endorsing, using the ground-boosted engine
   and stock turbo is actually much more dangerous. You have high air
   temperatures on the ground because of the boost so you need an
   expensive and power robbing intercooler.

   Then when you go a little higher, your manifold pressure starts to
   drop because the turbo is too small to keep up. You basically have a
   more powerful engine on the ground that loses power with altitude.

   And thn the stock turbo can fail like it did on Dave's plane. So
   then you have to buy new parts anyway. Plus the cost of the
   intercooler. This is not actually saving money compared to buying
   the big turbo from the start.

   Sure you could buy a Lycoming or Continental from the start if
   that's your preference. Nothing wrong with that. For your $70,000 or
   so for a turbo engine in the 300 hp class you get a fairly good
   engine. Still you can fry the engine pretty easily if you don't pay
   attention to EGT's, CHTs and leaning.

   According to the Columbia 400 POH, the plane has to be flown at a
   pretty rich mixture at altitude. Fuel burn is 25 gph at max cruise
   (85 percent power) at its FL250 celiing. That's a pretty rich
   mixture. The BSFC is about 0.57.

   By comparison, spending six or seven thousand bucks on a
   turbonormalized 2-rotor like I am proposing is a pretty good deal.
   Without exhaust valves to worry about you could cruise at a much
   leaner mxiture than the Continental and get far better mileage. With
   a flywheel magneto and mechanical fuel injection you would have as
   good or better reliability.


   Regards,

   Gordon.


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.