Subject: Pressure potting P-ports
From: Rotary Engine
Date: 12/19/2006, 8:49 PM
To: AARotary Engine



I have come up with a way of pressure potting P-ports.
This will guarantee they don't leak. Requires a bit of fabrication
of a fixture made from a little bit of Lexan and a hand tire pump.
Use 10-32 threaded rod to bolt it on the rotor housing.
The same tool can check the cured P-port for coolant
leaks up to 30 psi. I am in the process of building it
and trying it out. Here is a 3D of the idea.
You put  a small quantity of JB Weld in the rotor housing.
Just enough to fill about one quarter of the cavity volume
and cover the tube on one side.
You then bolt on the fixture with a rubber gasket and a bit of
wax paper on the bottom to keep JB Weld off the Lexan so it is
air tight. You then slowly apply pressure
and watch the JB Weld just start to squish out around the tube
both inside the rotor housing and out side the rotor housing.
Release the pressure quickly and let the JB Weld cure. You can
use the fast cure stuff if you wish. After it is cured you do
the other side the same way. After that is cured you remove
the fixture and add more JB Weld to the first side. Re pressurize.
If it holds the pressure you are home free. If not it will squeeze
out through any remaining leaks. Remove the pressure and let it
cure. Do the same thing to the other side. Repeat if necessary.
BTW I baked a left over cup puck of JB Weld in the oven at 350 F
and it lost a bit of hardness but it was no where near melting
or loosing it's strength. When it cooled off it regained its
hardness.
-------------------------------------
Went shopping today and bought the stuff for potting
another P-port. Looks like 3/8" thick Plexiglas is
about right for the covers. This is a 4" by 8" sheet
but 4" by 6" should work fine. The plastic shop in Burbank
cut it for me no charge. This stuff can be bought from McMaster
Carr as well. Get a special drill to drill plexi. The tubeless
tire valve is called a metal valve at Pep Boys but any tubeless
tire valve for a mag or aluminum wheel should work.
The more I think about this scheme the better I think
it will work. To do two rotor housings I am going to
cut four pieces of plexi so both can be done at one
sitting.
More about this in the next few days.
---------------------------------------------------
This is a 1 1/2 inch pipe scaffolding fitting I found at Industrial
Metal Supply in Burbank to simulate a rotor housing for testing
potting techniques. Cheaper ($16) and easier than real rotor
housings for experimentation. I bought a couple.
I found the 3/8th plexi and 10-32 all thread too wimpy for
sealing well so I changed to 1/2 inch aluminum plate and
1/4 inch all thread or screws if you can find them about six
inches long.
The initial test are working well. The JB Weld is
too viscous but high temp Devcon is also too viscous according to
the Devcon engineers I spoke with. I'll try thinning JB Weld in
the next couple of days with acetone as recommended by the
JB Weld folks. Heating it has its drawbacks. These test take
time as you must wait at least six hours for the JB Weld to
kick out.
Jerry, how viscous is that stuff you used. I forgot the brand
name. I might try what you used. Will you do me a favor and build
a pressure test rig like this and test your p-port rotor
housings for water jacket leaks? Also you could buy some JB Weld
and compare viscosities subjectively if you don't mind.
Paul Lamar ...No rotor no motor.
Sure,  I will do the test.   But right now my housings are in an
assembled engine.   Not the final assembly: and I will tear it down
soon.    The stuff I use is Duralco 4525.  I pours about like light
weight machine oil.  24 hrs to cure at room temp.      According to
the company it maintains is physical properties up to 500º.  Here is
what is said on the label:  "Duralco 4525 has superior electrical,
chemical and thermal resistance. Use for high performance bonding,
potting, sealing and coating."  Check out their web site for more
info.   It does cost more but I like it anyway.  The mixing ratio is
8 to 100.  We found this easy to do by using a large, graduated (cc)
syringe.   Jerry
Thanks for the info Jerry. I'll get some and try it.
Well if the engine is assembled all you need do is a pressure
check on the whole water jacket.
--  Paul Lamar ...No rotor no motor.
The "engine" is together just for the fabrication of intake and
exhaust.  No seals.  The rotors are setting on the bench.    Jerry
If you put some O-rings in there it would still work.
No need for rotors or the e-shaft. We just did one like
that at Mazdatrix. Works great for checking the leak integrity
of the cooling jacket. You can re use the O-rings as not running
it applies no heat to them. You want to do this anyway before
you run the engine. Bad news if you run the engine and you
find you have a water leak around the p-port tubes.
--  Paul Lamar ...No rotor no motor.

Paul I searched for Duraco 4525 and found a great site. Besides  offering
various high temp ceramic epoxies they offer moldable ceramic  blanket felt.
Just the ticket to wrap the turbine to keep the heat in or sandwich it
between the inner inconel and outer stainless jacket on the header  manifold.

http://www.cotronics.com/vo/cotr/fc_blankets.htm

Thanks Jerry for suggesting the product.


DougFir

I learned a few things today. The viscosity of JB Weld is
sensitive to the addition of acetone. As little as 1/4 teaspoon
of acetone will dramatically reduce the viscosity per set
of tubes of JB Weld. The people at JB Weld suggested I do this.

This appears to be the key. The first
batch should be about one tube set with one teaspoon worth
of acetone. Use paper Dixie cubs as acetone melts plastic
cups instantaneously. Wait about 6 to 12 hours before
applying pressure briefly. Let cure. Add another tube
set thinned with one teaspoon of acetone. Wait about 5 to
12 hours again. Apply pressure briefly. Let cure.
Check for leaks. If it is leaking you can find out
where by immersing the rotor housing in a tube of
water. If the leak is small use 1.5 teaspoons of
acetone to repair as that will flow into the smallest
of cervices.

The teaspoon measuring devices are sold in the grocery
stores.

It is absolutely mandatory that you prepare the aluminum
for bonding using the etch kit from West Systems. This all
sounds like a lot of trouble but it is easier done than said.

If you follow this procedure your P-port is guaranteed
not to leak.


Paul Lamar ...No rotor no motor.

I am not the only one but I have a lot of experience with WEST system
and their various products.  A long time ago I was building sailboats
out of wood veneer glued up with WEST.  At that time they came up
with a way to bolt down the deck winches by simply gluing the
threaded bolt into the wood deck bosses.  No thru drilling, no nut.
These winches  were subject to tons of force trying to pull them out
of the deck.  Later  the Gougeons came up with the idea of gluing the
lead ballast using a similar process.  The boat  was lowered on to
the lead keel which had the keel bolts cast in.  The bolts slid
through oversize holes in the wood keel which were then filled with
epoxy.  The lead was on to stay.  What has all this got to do with
potting p ports?  I do drift off topic more and more as the years go
by.    I have used so much WEST epoxy over the  years and have never
had a failure.   The aluminum etch works as advertised.  Good
idea.     Jerry



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.