Subject: Reducing the Weight of the Rotor
From: Rotary Engine
Date: 12/20/2006, 10:44 PM
To: AARotary Engine


     The rotor weighs about 9 pounds not 14 pounds.
I
      > think a composite
      > might work. Aluminum rotor with cast in
steel
      > inserts for
      > the apex seals.
      >
      > Paul Lamar ...No rotor no motor.



     Paul

     You are correct...9.2 lbs.

     The folks as
Mazdatrix(http://www.mazdatrix.com/)
     reduce the rotor weight of an RX-8 rotor to 9.0
by
     machining weight just inside the three
"corners".

     So my target weight would be...6.0 lbs, but any
weight
     reduction the further from the center the
better.

     David

David, is this for aircraft use? The best, most
economical and simplest
would be to do the end housings and intermediate
housings in plain old
ALUMINUM with a good coating, or to be really exotic
a cermet and ground
casting that is hard enough to run as is. There is
really no reason to
lighten the rotors at all. it is a part that WORKS
now. In an aircraft
you will never be using a high enough RPM that any
rotor weight
reduction would be helpful.

The only person that needs a lighter rotor
is the racer revving the engine to 10K RPM or
higher. If you feel really
flush cast the rotor in Titanium alloy 1/3 or more
lighter with no loss
of strength.

Side/end plates are where the real weight loss is to
be
had. Mazda has even done the parts already,
published a paper on it and
everything! The LeMans engine used detonation gun
coated and diamond
ground end and intermediate housings. They ran 24
hrs flat out and won
one of the worlds biggest races over all. This is
also the safest way to
lose weight off the engine, it has already been
tested by the factory!
Foamed metal and all this other stuff is fine, but
getting something to
market is the key.

A rotary with aluminum end and center housings would
have such a HP to weight advantage it isn't even
funny.
Bill Jepson


Bill

I've studied the Mazda docs. They certainly stripped
everything they could in the early 90s, and yes they
were so good that race changed a lot (and the race
folks changed the rules)

Yep, my uncle is flush. He wants a ultra lightweight
multi fuel rotor based engine that is reliable.
Production runs of 10 to start.

The cost of magnesium is now cheaper than aluminum but
a boron-mg is needed to hold things together. I'm
waiting on the diamond carbon technology to improve
but not holding my breath.

In the end any rotary engine mods are all about
dumping the heat. So the engine is modified to  make
really slick surfaces (supermaching, coatings, etc.),
put a nice high temp coat (current favorite is Silicon
Carbide), throw in more radiators (wet or dry), or
somehow use that heat productively.

I should say that is for the short block.

Everything else surrounding that engine from intake to
exhaust needs a good weight reduction program. THAT is
where the diamond carbon stuff might come in handy.

David



I use the rotary engine myself to understand new
materials and coatings coming on line. In the past
five years there have been a number of advancements,
some that haven't worked their way into the racing car
crowd even.



One thing which may have been overlooked here is that the weight of the
rotors helps to absorb the power impulses, so the less weight, the
sharper the pulses which are transmitted to the drive system.  I'm not
sure that the small amount of weight which could be taken off would be
worth it, especially if you started seeing damage to the reduction.

Also, it's my impression that the rotors store some energy, just like
the flywheel -- if so, the engine might not even run at all if they are
too light.
Keith Wood


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.