Subject: Reducing the Weight of the Rotor
From: Rotary Engine
Date: 12/21/2006, 9:01 AM
To: AARotary Engine


>>      The rotor weighs about 9 pounds not 14
pounds.
>> I
>>       > think a composite
>>       > might work. Aluminum rotor with cast in
>> steel
>>       > inserts for
>>       > the apex seals.
>>       >
>>       > Paul Lamar ...No rotor no motor.
>>
>>
>>
>>      Paul
>>
>>      You are correct...9.2 lbs.
>>
>>      The folks as
>> Mazdatrix(http://www.mazdatrix.com/)
>>      reduce the rotor weight of an RX-8 rotor to
9.0
>> by
>>      machining weight just inside the three
>> "corners".
>>
>>      So my target weight would be...6.0 lbs, but
any
>> weight
>>      reduction the further from the center the
>> better.
>>
>>      David
>>
>> David, is this for aircraft use? The best, most
>> economical and simplest
>> would be to do the end housings and intermediate
>> housings in plain old
>> ALUMINUM with a good coating, or to be really
exotic
>> a cermet and ground
>> casting that is hard enough to run as is. There
is
>> really no reason to
>> lighten the rotors at all. it is a part that
WORKS
>> now. In an aircraft
>> you will never be using a high enough RPM that
any
>> rotor weight
>> reduction would be helpful.
>>
>> The only person that needs a lighter rotor
>> is the racer revving the engine to 10K RPM or
>> higher. If you feel really
>> flush cast the rotor in Titanium alloy 1/3 or
more
>> lighter with no loss
>> of strength.
>>
>> Side/end plates are where the real weight loss is
to
>> be
>> had. Mazda has even done the parts already,
>> published a paper on it and
>> everything! The LeMans engine used detonation gun
>> coated and diamond
>> ground end and intermediate housings. They ran 24
>> hrs flat out and won
>> one of the worlds biggest races over all. This is
>> also the safest way to
>> lose weight off the engine, it has already been
>> tested by the factory!
>> Foamed metal and all this other stuff is fine,
but
>> getting something to
>> market is the key.
>>
>> A rotary with aluminum end and center housings
would
>> have such a HP to weight advantage it isn't even
>> funny.
>> Bill Jepson
> > > Bill
> > I've studied the Mazda docs. They certainly
stripped
> everything they could in the early 90s, and yes
they
> were so good that race changed a lot (and the race
> folks changed the rules)
> > Yep, my uncle is flush. He wants a ultra
lightweight
> multi fuel rotor based engine that is reliable.
> Production runs of 10 to start.
> > The cost of magnesium is now cheaper than aluminum
but
> a boron-mg is needed to hold things together. I'm
> waiting on the diamond carbon technology to
improve
> but not holding my breath.
> > In the end any rotary engine mods are all about
> dumping the heat. So the engine is modified to make
> really slick surfaces (supermaching, coatings,
etc.),
> put a nice high temp coat (current favorite is
Silicon
> Carbide), throw in more radiators (wet or dry), or
> somehow use that heat productively.
> > I should say that is for the short block.
> > Everything else surrounding that engine from
intake to
> exhaust needs a good weight reduction program.
THAT is
> where the diamond carbon stuff might come in
handy.
> > David

> I use the rotary engine myself to understand new
> materials and coatings coming on line. In the past
> five years there have been a number of
advancements,
> some that haven't worked their way into the racing
car
> crowd even.



One thing which may have been overlooked here is
that the weight of the
rotors helps to absorb the power impulses, so the
less weight, the
sharper the pulses which are transmitted to the
drive system.  I'm not
sure that the small amount of weight which could be
taken off would be
worth it, especially if you started seeing damage to
the reduction.

Also, it's my impression that the rotors store some
energy, just like
the flywheel -- if so, the engine might not even run
at all if they are
too light.
Keith Wood


Keith

For those reasons and more we have the rotor as the
last thing on our list to lighten.

However, it's a long lead item so we just started
doing  more research on the rotor system before the
holidays.


David


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.