Subject: Pressure potting P-ports
From: Rotary Engine
Date: 12/29/2006, 2:43 PM
To: AARotary Engine


     >>>> I have come up with a way of pressure potting P-ports.
     >>>> This will guarantee they don't leak. Requires a bit of
    fabrication
     >>>> of a fixture made from a little bit of Lexan and a hand tire pump.
     >>>> Use 10-32 threaded rod to bolt it on the rotor housing.
     >>>> The same tool can check the cured P-port for coolant
     >>>> leaks up to 30 psi. I am in the process of building it
     >>>> and trying it out. Here is a 3D of the idea.
     >>>> You put  a small quantity of JB Weld in the rotor housing.
     >>>> Just enough to fill about one quarter of the cavity volume
     >>>> and cover the tube on one side.
     >>>> You then bolt on the fixture with a rubber gasket and a bit of
     >>>> wax paper on the bottom to keep JB Weld off the Lexan so it is
     >>>> air tight. You then slowly apply pressure
     >>>> and watch the JB Weld just start to squish out around the tube
     >>>> both inside the rotor housing and out side the rotor housing.
     >>>> Release the pressure quickly and let the JB Weld cure. You can
     >>>> use the fast cure stuff if you wish. After it is cured you do
     >>>> the other side the same way. After that is cured you remove
     >>>> the fixture and add more JB Weld to the first side. Re pressurize.
     >>>> If it holds the pressure you are home free. If not it will squeeze
     >>>> out through any remaining leaks. Remove the pressure and let it
     >>>> cure. Do the same thing to the other side. Repeat if necessary.
     >>>> BTW I baked a left over cup puck of JB Weld in the oven at 350 F
     >>>> and it lost a bit of hardness but it was no where near melting
     >>>> or loosing it's strength. When it cooled off it regained its
     >>>> hardness.
     >>>> -------------------------------------
     >>>> Went shopping today and bought the stuff for potting
     >>>> another P-port. Looks like 3/8" thick Plexiglas is
     >>>> about right for the covers. This is a 4" by 8" sheet
     >>>> but 4" by 6" should work fine. The plastic shop in Burbank
     >>>> cut it for me no charge. This stuff can be bought from McMaster
     >>>> Carr as well. Get a special drill to drill plexi. The tubeless
     >>>> tire valve is called a metal valve at Pep Boys but any tubeless
     >>>> tire valve for a mag or aluminum wheel should work.
     >>>> The more I think about this scheme the better I think
     >>>> it will work. To do two rotor housings I am going to
     >>>> cut four pieces of plexi so both can be done at one
     >>>> sitting.
     >>>> More about this in the next few days.
     >>>> ---------------------------------------------------
     >>>> This is a 1 1/2 inch pipe scaffolding fitting I found at
    Industrial
     >>>> Metal Supply in Burbank to simulate a rotor housing for testing
     >>>> potting techniques. Cheaper ($16) and easier than real rotor
     >>>> housings for experimentation. I bought a couple.
     >>>> I found the 3/8th plexi and 10-32 all thread too wimpy for
     >>>> sealing well so I changed to 1/2 inch aluminum plate and
     >>>> 1/4 inch all thread or screws if you can find them about six
     >>>> inches long.
     >>>> The initial test are working well. The JB Weld is
     >>>> too viscous but high temp Devcon is also too viscous according to
     >>>> the Devcon engineers I spoke with. I'll try thinning JB Weld in
     >>>> the next couple of days with acetone as recommended by the
     >>>> JB Weld folks. Heating it has its drawbacks. These test take
     >>>> time as you must wait at least six hours for the JB Weld to
     >>>> kick out.
     >>>> Jerry, how viscous is that stuff you used. I forgot the brand
     >>>> name. I might try what you used. Will you do me a favor and build
     >>>> a pressure test rig like this and test your p-port rotor
     >>>> housings for water jacket leaks? Also you could buy some JB Weld
     >>>> and compare viscosities subjectively if you don't mind.
     >>>> Paul Lamar ...No rotor no motor.
     >>> Sure,  I will do the test.   But right now my housings are in an
     >>> assembled engine.   Not the final assembly: and I will tear it down
     >>> soon.    The stuff I use is Duralco 4525.  I pours about like light
     >>> weight machine oil.  24 hrs to cure at room temp.      According to
     >>> the company it maintains is physical properties up to
    500º.  Here is
     >>> what is said on the label:  "Duralco 4525 has superior electrical,
     >>> chemical and thermal resistance. Use for high performance bonding,
     >>> potting, sealing and coating."  Check out their web site for more
     >>> info.   It does cost more but I like it anyway.  The mixing
    ratio is
     >>> 8 to 100.  We found this easy to do by using a large, graduated
    (cc)
     >>> syringe.   Jerry
     >>> Thanks for the info Jerry. I'll get some and try it.
     >>> Well if the engine is assembled all you need do is a pressure
     >>> check on the whole water jacket.
     >>> --  Paul Lamar ...No rotor no motor.
     >> The "engine" is together just for the fabrication of intake and
     >> exhaust.  No seals.  The rotors are setting on the bench.    Jerry
     >> If you put some O-rings in there it would still work.
     >> No need for rotors or the e-shaft. We just did one like
     >> that at Mazdatrix. Works great for checking the leak integrity
     >> of the cooling jacket. You can re use the O-rings as not running
     >> it applies no heat to them. You want to do this anyway before
     >> you run the engine. Bad news if you run the engine and you
     >> find you have a water leak around the p-port tubes.
     >> --
     >> Paul Lamar ...No rotor no motor.
     >
     > Paul I searched for Duraco 4525 and found a great site. Besides
     > offering
     > various high temp ceramic epoxies they offer moldable ceramic
     > blanket felt.
     > Just the ticket to wrap the turbine to keep the heat in or
    sandwich it
     > between the inner inconel and outer stainless jacket on the header
     > manifold.
     >
     > http://www.cotronics.com/vo/cotr/fc_blankets.htm
     >
     > Thanks Jerry for suggesting the product.
     >
     >
     > DougFir
     >
     > I learned a few things today. The viscosity of JB Weld is
     > sensitive to the addition of acetone. As little as 1/4 teaspoon
     > of acetone will dramatically reduce the viscosity per set
     > of tubes of JB Weld. The people at JB Weld suggested I do this.
     >
     > This appears to be the key. The first
     > batch should be about one tube set with one teaspoon worth
     > of acetone. Use paper Dixie cubs as acetone melts plastic
     > cups instantaneously. Wait about 6 to 12 hours before
     > applying pressure briefly. Let cure. Add another tube
     > set thinned with one teaspoon of acetone. Wait about 5 to
     > 12 hours again. Apply pressure briefly. Let cure.
     > Check for leaks. If it is leaking you can find out
     > where by immersing the rotor housing in a tube of
     > water. If the leak is small use 1.5 teaspoons of
     > acetone to repair as that will flow into the smallest
     > of cervices.
     >
     > The teaspoon measuring devices are sold in the grocery
     > stores.
     >
     > It is absolutely mandatory that you prepare the aluminum
     > for bonding using the etch kit from West Systems. This all
     > sounds like a lot of trouble but it is easier done than said.
     >
     > If you follow this procedure your P-port is guaranteed
     > not to leak.
     >
     >
     > Paul Lamar ...No rotor no motor.

    I am not the only one but I have a lot of experience with WEST system
    and their various products.  A long time ago I was building sailboats
    out of wood veneer glued up with WEST.  At that time they came up
    with a way to bolt down the deck winches by simply gluing the
    threaded bolt into the wood deck bosses.  No thru drilling, no nut.
    These winches  were subject to tons of force trying to pull them out
    of the deck.  Later  the Gougeons came up with the idea of gluing the
    lead ballast using a similar process.  The boat  was lowered on to
    the lead keel which had the keel bolts cast in.  The bolts slid
    through oversize holes in the wood keel which were then filled with
    epoxy.  The lead was on to stay.  What has all this got to do with
    potting p ports?  I do drift off topic more and more as the years go
    by.    I have used so much WEST epoxy over the  years and have never
    had a failure.   The aluminum etch works as advertised.  Good
    idea.     Jerry




Guys, Sorry for bring stupid, but why do not you just TIG weld it at an
engineering shop ?.. A good TIG weld should be good enough to seal 9 bar
of pressure

regards
Roderick

That might work and somebody needs to try it with some old
rotor housings. The problem is the rotor housings might
warp destroying the gas and coolant seal between rotor housing
and end housing. As little as .003 of an inch distortion will destroy
the seal. Way less than that if the apex seal wear surface is
distorted.

If one were to try it I suggesting grinding away
these surfaces first so a 360 degree tig weld can be made.
Tig welding should be done in chunks so the rotor housing can cool
off. If the rotor housing gets to 500 F the heat treat
could be affected. In any event it is an R&D project
and must be tested.

Paul Lamar ...No rotor no motor.


Paul,
I have seen some massive P-ports Tig welded locally - no distortion or
sealing problems.
George (down under)


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.