Subject: Diesel turbo charger turbine & compressor power
From: Rotary Engine
Date: 12/31/2006, 1:16 PM
To: AARotary Engine




   I just ran across these interesting charts from
   a tech paper Caterpillar did on turbo compounding
   diesel engines. Diesel engines have way less waste
   heat/HP/kinetic energy in the exhaust than gasoline
   piston engines and rotaries. Despite this they were able to
   reduce the fuel consumption as much as 10% at sea level and
   full power at 1800 RPM.

   --
   Paul Lamar ...No rotor no motor.

   Paul,

   I am a neophyte to homebuilt aircraft and am looking at a couple of
   designs that I want to use the rotary with. Info I have read seems to
   say there is a bit of wasted charge sent out the exhaust. I've been
   trying to keep up with your turbo compounding theories and I must say it
   is very intriguing. Is something akin to this setup Caterpillar has
   designed feasible for the 13? Is it cost effective and would it be able
   to be engineered into a homebuilt? I'm not sure of the 13's exhaust
   temperature but I know that it's pretty high. Would it need to be
   cooled prior to entering turbine or is it more feasible to use exotic
   metals on the turbo's intake section? I'm presently looking at the
   Bearhawk and the Bede Corps BD-4(preferable). I'm not an engine "type"
   guy, but have no qualms learning my way into that category. Thanks
   again for all the work you do and information that you disseminate.

   Allen Slominski
   Houston, TX

   Well the exhaust energy is a bit higher for the rotary than it is
   for a piston engine but only about 5% or so more. Say 50% rather
   than 45%. The big difference is two thirds of the exhaust energy
   is dissipated by the exhaust valves in a piston engine. All engines
   have a heat balance where the percentages of the energy in a gallon
   of gas is distributed to various systems in the engine.
   I assume you have read http://www.rotaryeng.net/turbo.html

   Building a turbo compound yourself is very expensive. I have
   spent $7,000 on the project so far but I have a few contacts
   in the aerospace biz and they tell me a large company is working
   on it for small UAV rotary engines. Plenty of tech papers have
   been written on the rotary turbo compound. Mostly computer
   simulations. Most are very positive. So far no rotary based hardware
   has been built to my knowledge yet.

   I am waiting until I get more info from that source
   as it will save me doing a lot of very expensive R&D. Hopefully it
   will not be classified. If developed for the worlds cars a
   theoretical 20% in fuel consumption world wide is possible. If you
   can't wait and want to try it yourself I will give you all the help
   I can including loaning you my $7,000 turbo charger gear box.

   The technology is 70 years old so it should not be all that
   hard. Yes you can cool the exhaust but in theory that wastes
   some of the energy in the exhaust. Better to deal with the
   heat. One way is use a thermo pile ahead of the exhaust turbine
   to extract some of the heat as electrical power and cool the exhaust
   a bit. http://www.harvestfields.ca/etextLinks/16/05.htm


   Paul Lamar ...No rotor no motor.


Paul,

Thanks for the information and consideration.  My youngest daughters
(32) boyfriend owns a very busy machine shop with his dad.  I maybe able
to get things done at a "reasonable" rate when the time comes.  I
haven't had him do anything for me yet.  I haven't read the entire site
under the turbo heading, but about 40%.  I am an engineer, but a control
systems type and don't have that much mechanical training.  I would
probably not be the guy you would want doing the calcs for the project.
But if there is any way I can help, I would be glad to.  Please excuse
my ignorance, but didn't Mazda produce a turbo charger for some of their
cars?  I haven't done enough research to know those things and if their
existing design was something that could be used as a starting point.

Allen Slominski

Yes Mazda made a 3 rotor turbo in 1990's and a two rotor starting
in 1988 through 2003. Mostly for sale in the rest of the world.
They stopped selling them in the US in 1994 or so.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.