Subject: Diesel turbo charger turbine & compressor power
From: Rotary Engine
Date: 12/31/2006, 1:18 PM
To: AARotary Engine


   I just ran across these interesting charts from
   a tech paper Caterpillar did on turbo compounding
   diesel engines. Diesel engines have way less waste
   heat/HP/kinetic energy in the exhaust than gasoline
   piston engines and rotaries. Despite this they were able to
   reduce the fuel consumption as much as 10% at sea level and
   full power at 1800 RPM.

   --
   Paul Lamar ...No rotor no motor.

   Paul,

   I am a neophyte to homebuilt aircraft and am looking at a couple of
   designs that I want to use the rotary with. Info I have read seems to
   say there is a bit of wasted charge sent out the exhaust. I've been
   trying to keep up with your turbo compounding theories and I must say it
   is very intriguing. Is something akin to this setup Caterpillar has
   designed feasible for the 13? Is it cost effective and would it be able
   to be engineered into a homebuilt? I'm not sure of the 13's exhaust
   temperature but I know that it's pretty high. Would it need to be
   cooled prior to entering turbine or is it more feasible to use exotic
   metals on the turbo's intake section? I'm presently looking at the
   Bearhawk and the Bede Corps BD-4(preferable). I'm not an engine "type"
   guy, but have no qualms learning my way into that category. Thanks
   again for all the work you do and information that you disseminate.

   Allen Slominski
   Houston, TX

   Well the exhaust energy is a bit higher for the rotary than it is
   for a piston engine but only about 5% or so more. Say 50% rather
   than 45%. The big difference is two thirds of the exhaust energy
   is dissipated by the exhaust valves in a piston engine. All engines
   have a heat balance where the percentages of the energy in a gallon
   of gas is distributed to various systems in the engine.
   I assume you have read http://www.rotaryeng.net/turbo.html

   Building a turbo compound yourself is very expensive. I have
   spent $7,000 on the project so far but I have a few contacts
   in the aerospace biz and they tell me a large company is working
   on it for small UAV rotary engines. Plenty of tech papers have
   been written on the rotary turbo compound. Mostly computer
   simulations. Most are very positive. So far no rotary based hardware
   has been built to my knowledge yet.

   I am waiting until I get more info from that source
   as it will save me doing a lot of very expensive R&D. Hopefully it
   will not be classified. If developed for the worlds cars a
   theoretical 20% in fuel consumption world wide is possible. If you
   can't wait and want to try it yourself I will give you all the help
   I can including loaning you my $7,000 turbo charger gear box.

   The technology is 70 years old so it should not be all that
   hard. Yes you can cool the exhaust but in theory that wastes
   some of the energy in the exhaust. Better to deal with the
   heat. One way is use a thermo pile ahead of the exhaust turbine
   to extract some of the heat as electrical power and cool the exhaust
   a bit. http://www.harvestfields.ca/etextLinks/16/05.htm


   Paul Lamar ...No rotor no motor.


   Guys,
   Have you ever thought of using Garret VNT turbos. I receive the Garret
   Boost Mag as a one of their supplier, and all new turbos for diesels are
   VNT (Variable Geometry). Basically the principle works by closing
   "camera
   eye type" flaps are low revs to increase exhaust velocity thus it reach
   working rpm at very low revs.. these flaps open up in proportion to rpm
   thus keeping the exhaust speed constant. According to Garret fuel
   consumption and turbo lag improved significantly, thus it is now
   allowing automotive companies to design smaller but yet more power
   diesel and gas engines through this technology
   regards
   Roderick

   Yes we have considered it and yes it is a very good idea. Makes it
   much much easier to match the turbine HP to our requirements
   both turbo compound and straight turbo charger.
   Can you scan some relevant pictures from the mag and send them
   to us?

   Paul Lamar ...No rotor no motor.


Paul,

I would appreciate seeing anything you think might be a viable
alternative for the application we've been talking about.

Allen Slominski


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.