Subject: Diesel turbo charger turbine & compressor power
From: Rotary Engine
Date: 1/1/2007, 7:30 PM
To: AARotary Engine


     I just ran across these interesting charts from
     a tech paper Caterpillar did on turbo compounding
     diesel engines. Diesel engines have way less waste
     heat/HP/kinetic energy in the exhaust than gasoline
     piston engines and rotaries. Despite this they were able to
     reduce the fuel consumption as much as 10% at sea level and
     full power at 1800 RPM.

     --
     Paul Lamar ...No rotor no motor.

     Paul,

     I am a neophyte to homebuilt aircraft and am looking at a couple of
     designs that I want to use the rotary with. Info I have read seems to
     say there is a bit of wasted charge sent out the exhaust. I've been
     trying to keep up with your turbo compounding theories and I must say
it is very intriguing. Is something akin to this setup Caterpillar has
designed feasible for the 13? Is it cost effective and would it be able to
be engineered into a homebuilt? I'm not sure of the 13's exhaust
temperature but I know that it's pretty high. Would it need to be cooled
prior to entering turbine or is it more feasible to use exotic metals on
the turbo's intake section? I'm presently looking at the Bearhawk and the
Bede Corps BD-4(preferable). I'm not an engine "type" guy, but have no
qualms learning my way into that category. Thanks again for all the work
you do and information that you disseminate.

     Allen Slominski
     Houston, TX

     Well the exhaust energy is a bit higher for the rotary than it is
     for a piston engine but only about 5% or so more. Say 50% rather
     than 45%. The big difference is two thirds of the exhaust energy
     is dissipated by the exhaust valves in a piston engine. All engines
     have a heat balance where the percentages of the energy in a gallon
     of gas is distributed to various systems in the engine.
     I assume you have read http://www.rotaryeng.net/turbo.html

     Building a turbo compound yourself is very expensive. I have
     spent $7,000 on the project so far but I have a few contacts
     in the aerospace biz and they tell me a large company is working
     on it for small UAV rotary engines. Plenty of tech papers have
     been written on the rotary turbo compound. Mostly computer
     simulations. Most are very positive. So far no rotary based hardware
     has been built to my knowledge yet.

     I am waiting until I get more info from that source
     as it will save me doing a lot of very expensive R&D. Hopefully it
     will not be classified. If developed for the worlds cars a
     theoretical 20% in fuel consumption world wide is possible. If you
     can't wait and want to try it yourself I will give you all the help
     I can including loaning you my $7,000 turbo charger gear box.

     The technology is 70 years old so it should not be all that
     hard. Yes you can cool the exhaust but in theory that wastes
     some of the energy in the exhaust. Better to deal with the
     heat. One way is use a thermo pile ahead of the exhaust turbine
     to extract some of the heat as electrical power and cool the exhaust
     a bit. http://www.harvestfields.ca/etextLinks/16/05.htm


     Paul Lamar ...No rotor no motor.


     Guys,
     Have you ever thought of using Garret VNT turbos. I receive the Garret
     Boost Mag as a one of their supplier, and all new turbos for diesels
are VNT (Variable Geometry). Basically the principle works by closing
"camera
     eye type" flaps are low revs to increase exhaust velocity thus it
reach working rpm at very low revs.. these flaps open up in proportion to
rpm thus keeping the exhaust speed constant. According to Garret fuel
consumption and turbo lag improved significantly, thus it is now allowing
automotive companies to design smaller but yet more power diesel and gas
engines through this technology
     regards
     Roderick

     Yes we have considered it and yes it is a very good idea. Makes it
     much much easier to match the turbine HP to our requirements
     both turbo compound and straight turbo charger.
     Can you scan some relevant pictures from the mag and send them
     to us?

     Paul Lamar ...No rotor no motor.


Paul,

I would appreciate seeing anything you think might be a viable
alternative for the application we've been talking about.

Allen Slominski


Does anyone have a clue the velocity of the gases leaving the exhaust port at
6000 rpm full throttle (under take off conditions and cruise if possible).

Thanks,
Brent Hasty

Not really. My guess is supersonic from the sound it makes.
It is also a function of the e-shaft angle, the pressure in the
the exhaust chamber, the pressure in the exhaust pipe and the
area of the exhaust port. You can speed up and slow down the
speeds by changing the diameter of the exhaust pipe.

All we have is this chart of exhaust pressure.
http://www.rotaryeng.net/Mazda-p-port-press-wave-enhanced.jpg

Some smart people might be able to calculate the average mass
air flow by knowing what goes in the engine and adding the heat
factor. (P1 X V1)/T1 = (P2 X V2)/T2

V1 would be volume of air going into the engine in unit
time. P1 is the pressure going in and T1 is the absolute
temperature (Kelvin) of the air going in.
http://en.wikipedia.org/wiki/Kelvin

The speed of the air is cubic ft per second (volume in unit time)
divided by the area of the pipe in square feet. That gives the speed
of the air in feet per second. In other words 100 cubic feet
per second flowing in a one square foot area pipe would be
100 feet per second.


Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.