Subject: ceramic rotary single rotor 13b
From: Rotary Engine
Date: 1/6/2007, 5:45 PM
To: AARotary Engine


> Hi
> I am new to this list (this is my first post) and have been following the
> various discussions with interest.
> With regards to the lightweight single rotor e shaft I have some very good
> contacts in Asia (I work there) who can knock up stuff cheaply and of good
> quality. George I am a fellow Aussie too, I would imagine that every CNC in
> Aust is machining parts for the mining industry, probably easier and
> cheaper
> to get the e/shafts done in Asia.
>
> Anyway I started thinking that two issues with rotaries being widely
> accepted in aviation are a) need for PSRU and b) cooling.
> I know that my sources in Asia could knock out all the lightweight bits to
> assemble a light rotary eng and with some engineering it should be able to
> be assembled and offered for sale with a built-in PSRU.
> However it is the cooling side of things that worries me. It is
> difficult to
> offer an off-the-shelf ready to go engine when the reliability is dependent
> upon the correct installation of a cooling system. So I did some searching
> on ceramic rotaries and came up with the below. Forgive me if this info has
> already been discussed/posted.
> Does anyone know of any other companies attempting this? Are there other
> ways to run a rotary at high temps and lose the cooling systems?
> Forgive me if these sound ignorant questions. I am on a fast learning
> track.
> It is my dream to build a plane and to use a rotary.
>
> Regards Ron (In Japan)
>
> Making An All-Ceramic Wankel Engine - Progress
>
> from http://ceramicrotaryengines.com/
>
> The image opposite is a photo of a small Wankel Rotor we ordered to
> specification. It is made out of CeTZP (zirconia) ceramic. The ceramic
> manufacturer shaped the CeTZP rotor in the green (soft) state and was
> subsequently sintered (in a furnace).
>
> The combustion chambers on the rotor faces and the slots at the apex where
> the tip seals are to be located have yet to be machined. It is likely that
> this will be done in the hardened state to ensure that tight tolerances
> will
> be met. The gear will be made out of steel and fitted into the central
> recesses. The low thermal conductivity of the CeTZP ceramic should ensure
> that the steel gearing is kept from overheating.
>
> We are considering making the Wankel housing out of CeTZP ceramic as well.
> This should ensure that the heat generated during the combustion of fuel
> will be retained within the walls of the combustion chamber. A CeTZP
> ceramic
> Wankel engine should not require liquid cooling.


Great idea -- but think of the COST.

The one real advantage we've got is the ready availability of cheap
Mazda engines.  They do just about all of the expensive and difficult
stuff for us, all we have to do is figure out how to make that work to
suit our needs.

If that ceramic engine could be produced and sold for a price lower than
the competing reciprosaur, it would have great potential.

I remember when there were only three common options for experimental
aircraft engines -- buy a "real" airplane engine, or mount a VW or
Corvair conversion.  It wasn't until they started bolting 2-strokes on
hang gliders that any other options became popular.  The 4-stroke
Rotaxes wouldn't exist except for all the money that Bombardier got
selling 2-strokes for aviation.  This made them aware of the need for an
alternative.

But if you look at the costs of the 912 and 914, you see that there is
still an untapped market for a lightweight, inexpensive 100HP engine,
and this is a place that a ceramic engine could take over if it were
viable and proven.

I've emailed them for more information, and if this comes off will be
happy to note them as a developmental technology.

Thanks,
Keith


iRobot make some cool military robots but the thing that keeps them
afloat is their mass market Roomba. Electric generators for mobile
power and trains, places where turbines have been used, are the
closest mass market for the kind of engines used in aircraft. Constant
high power output without the RPM going up and down a lot like in a
car. Have you ever lifted one of those portable generators? They need
weight reduction.

Sell engines to generator companies and then make sure all the
equipment you buy can also be used to make airplane engines.
-Jeff


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.