Subject: The gear ratio question (2)
From: Rotary Engine
Date: 1/10/2007, 12:52 PM
To: AARotary Engine




         Hi Paul,

         Maybe in a few words I can clarify the gear concept. You've
   said this
   in
         different words before so if I'm too far off base please edit.

         The gears inside the rotary are a means of  "timing"  the
   position of
         the rotor. Very much akin to the way   "timing"  gears ( or
   chains or
         cog belts )  "Time"  the position of the CAMshaft in an auto
         engine.  *** POWER is not transmitted in either case, only the
   exact
         POSITION is determined.***  This  "timing"  is necessary to
   put the
         piston engine valves in the proper place at the proper time,
   in the
         rotary this  "timing"  is necessary to put the rotor in the proper
         place
         at the proper time.

         Concept any clearer or did I muddy the waters even more.
         Dave

         Excellent. Much better than I could have put it. Very concise.

         Paul Lamar ...No rotor no motor.

   Yes..  That is very good.  Can I help with the language?

   The gears inside the rotary are a means of  "timing"  the position and
   orientation of the rotor.  This is very much akin to the way
   "timing"  gears ( or chains or cog belts )  "time"  the position of the
   CAMshaft in a piston engine.  *** POWER is not transmitted in either
   case, only the exact POSITION is determined.***  This  "timing"  is
   necessary to put the piston engine valves in the proper place at the
   proper time.  In the rotary this "timing" is necessary to put the rotor
   in the proper place and orientation at the proper time.


   Matt-


   I'll still act dense here.

   It seems that "timing" (except ignition timing, which can be handled
   in many
   ways) is a function of the placement and shape of the ports. Since
   the ports
   are open and closed by the position of the rotor and the rotor will
   go as
   fast as its load, design, and inputs allow it, where is the "timing"
   issue?

   Ports will be open whenever the rotor isn't blocking them, unlike
   the valves
   in a piston engine, which will open when the camshaft says. If a cam
   belt or
   chain slips a tooth, valve timing will change; what can change in a
   rotary?

   Tim Kern

   Nothing. If it slips a tooth it will jam. Extremely rare occurrence.
   Far less of an occurrence than a cam changing timing due to worn
   teeth. Engine can be over hauled several times without replacing
   the static or rotor gear.

   BTW p-ports never close. As the chambers comes by the ports two
   chambers can be open at the same time. The rotary is closer to a
   continuous combustion engine (jet) than it is to a intermittent
   combustion (piston) engine.

   Paul Lamar ...No rotor no motor.


Maybe I can try again...  Requoting:

The gears inside the rotary are a means of  "timing"  the position and
orientation of the rotor.  This is very much akin to the way
"timing"  gears ( or chains or cog belts )  "time"  the position of the
CAMshaft in a piston engine.  *** POWER is not transmitted in either
case, only the exact POSITION is determined.***  This  "timing"  is
necessary to put the piston engine valves in the proper place at the
proper time.  In the rotary this "timing" is necessary to put the rotor
in the proper place and orientation at the proper time.

>From dictionary.com <http://dictionary.com>: Timing: 1.the system of
those sequential relations that any event has to any other, as past,
present, or future; indefinite and continuous duration regarded as that
in which events succeed one another.

"Timing" in this context is not about seconds, minutes, or hours so much
as it is about the precise order in which things happen.  "Timing" an
engine is about degrees of rotation of some shaft in the engine,
regardless of RPM.  This means that "timing" is not about "time," but
about the order of operation.

So, rewriting the above...

The gears inside the rotary are a means of  controlling the position and
orientation of the rotor within the housing.  This is very much akin to
the way timing gears ( or chains or cog belts )  "time"  the position of
the CAMshaft in a piston engine.  *** POWER is not transmitted in either
case, only the exact POSITION and ORIENTATION of various pieces are
determined.***  This  "timing"  is necessary to put the piston engine
valves in the proper place at the proper time.  In the rotary this
"timing" is necessary to put the rotor in the proper place and
orientation at the proper time.  The gears force the rotor to be
oriented correctly at any given position of the e-shaft in order for the
combustion cycles to take place.


Other things to consider:

Without the correct gearing, the rotor would be free to rotate on the
e-shaft.  This would allow (among other things), depending on how the
rotor was oriented, gases to travel from above one rotor face to an
adjacent face by passing around the end of the apex of the rotor.

Many piston engines will "jam" if the cam slips a tooth - a valve will
contact a piston.


Regards,

Matt-



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.