Subject: Warp Drive Prop cut down was props
From: Rotary Engine
Date: 1/29/2007, 5:18 AM
To: AARotary Engine


       > Bill Eslick has run a bunch of interesting prop tests and
       > published the data on his web site. http://www.weslick.com/
       > I reproduced some of it here and added some comments.
       > The airplane is running into a brick wall at 165 MPH.
       > Increasing the power does not help and just burns more
       > fuel. It does not result in an increase of airspeed.
       >
       > My theory is the prop tips are stalling and running
       > into the high drag transonic region at the same time.
       >
       > Quoting Bill:
       > "I used a Props, Inc. 67 x 68 wood prop, a Felix Bi-Cambered
       > 68 x 72 wood prop, and a Warp Drive three-blade ground adjustable
       > carbon-fiber prop."
       >
       > Quoting Jordonoff:
       > "If the propeller were turning in solid material, as is the case with
       > a screw in wood, it could act without slipping, and so the distance
       > traveled in one revolution would be equal to the theoretical travel
       > of the propeller. Inasmuch as the propeller is turning in the air,
       > however, there is a certain amount of slip; there fore its actual
       > travel distance falls short of its theoretical travel distance."
       >
       > The ratio of how far it would screw into wood to how far it would
       > screw into air is called the Advance Ratio. IMHO these props are
       > at the limit of the advance ratio.
       >
       > The Warp Drive have no twist so the tip drag is higher.
       >
       > The tip thickness is as follows.
       > Felix: 0.235" Props, Inc: 0.420" Warp: 0.272"
       >
       > I am guessing here. The solution might be more blade area with
       > a shorter prop. The Warp drive blades can be modified by
       > cutting off the aft part of the blade at an angle and sanding
       > them in such a way as to reduce the tip angle of attack and hence
       > the drag. However one would probably have to add another blade.
       > I'll do a 3D shortly
       >
       > What is your theory on what is happening?

       > Paul Lamar


      The Warp Drive prop has very little twist - about 13 deg and was
      designed
      and
      optimized for ultralights and 100 mph operation. At higher speeds, the
      inboard
      sections of the prop are actually going into reverse thrust. Look at the
      prop
      and see if you have any bugs on the forward face of the prop. There
      should
      be none, only on the back of the prop (this is near the hub).
      I had the same problem with my 125 hp Soob EA81 powered Europa and
      after doing the research went to a Catto custom fixed pitch. WOT speed
      instantly jumped from 150 to 175 mph with no other changes. Climb stayed
      the same.
      The Catto has 40-45 deg twist at the root. This is so at higher
      speeds, the
      hub area is still at a positive angle of attack to the relative wind.
      I had no idea what was going on and I emailed Stuart Gort at Powerfin
      Props and he was
      very helpful with the following:

      The Powerfin B-model has only about 2 more degrees of twist than the
      Warp. The twist is important on your application because as you
      approach the
      fast part of the flight envelope, the inboard sections of the prop
      begin to
      go into beta mode. This means the air is being accelerated over the
      lower
      camber faster than over the upper camber, essentially making reverse
      thrust
      (or at least making enough drag to be the main factor in achieving
      equilibrium - no more acceleration). Our prop, because of the 2 more
      degrees
      might have some positive effect but I wouldn't bet the farm on it.
      Chances
      are that any improvement would be negligible. For airplanes in the
      135 mph
      range, a proper design might have about 40 - 50 degrees of twist
      from the
      tip to the most inboard definable sections. A Warp, at 64" has about 13
      degrees. So, the lack of twist on the Warp and the resulting drag on the
      inboard stations is certainly slowing you down but there is no off
      the shelf
      design out there yet that can well accommodate your plane.

      Stuart Gort
      Powerfin Props
      GLENN CROWDER


      The point here is modifying the Warp drive prop
      you might have instead of spending big bucks on
      new props until you find one that works.
      That is if you can even find a properly twisted all carbon
      blade with sufficient blade area to absorb the rotary HP
      that can be ground adjustable in pitch.

      The Warp Drive blade can be set up in a mill at just the right
      angles and the bottom milled off flat. If you keep
      the set up support you could mill all four blades
      which is what I think one is going to need for blade area
      when you cut the prop down to about 64 inches dia. or so.
      (To lower the tip Mach number.)

      No doubt about it. It is a compromise and far from
      perfect. Final shaping can be done with a block sander.

      I am not sure this is going to work but it might be worth
      a try. Cheaper than up grading one's PSRU to a 2.85:1.

      BTW Perry Mick do you think you can duplicate Bill Eslicks
      test with your current prop? As I recall you are also
      running a 2.17:1 PSRU. That will give us some more data
      to go on. These airplanes should be going
      faster with all that HP.

      -------------------------------------------------------
      To illustrate the importance of the prop tip on the overall
      efficiency of the prop I wrote a short Quick BASIC program
      to calculate just the HP consumed by a very small 3 inch by
      3 inch section of the blade tip. The last segment of the blade.
      The diameter of this prop is only 61.5 inches. I can do a whole
      series of diameters however. The larger the diameter the worse
      the drag at a given RPM. Particularly at high speeds were the
      forward velocity of the airplane adds to the vector sum of the
      tip velocity. Not done yet in this program. If one does this
      one winds with a lot of tables or curves.

      The drag coef. (cd) used are from Von Doenhoff classic book "Theory
      of Wing Sections". The total HP consumed by the prop is the
      addition of the HP consumed from all the segments from the hub
      to the tip. As you can see the HP consumed rapidly increases
      as the RPM and the section drag coefficient goes up. This is
      why efficient props are tapered and the tips are thin. The thinner
      the better. This is where carbon fiber comes into the picture.
      Carbon fiber has a higher strength to density ratio so it is ideal
      for anything that rotates at high speed. The blade is also twisted
      to near zero angle of attack and, in some cases, are swept back
      to minimize tip transonic drag.

      There are some spread sheets around that do this but I find Quick
      BASIC to be quicker. If anybody wants to use QB or learn it
      let me know. IMHO it is the easiest programming language to learn of
      all the programming languages. If you wish to try doing a spread
      sheet I can send you the source code for this calculation so you
      can see and use the formulas I used.

      Paul Lamar ...No rotor no motor.

      Paul,

      I'm going to try to work up a spreadsheet that will give some useful
      calculations for preliminary sizing of propellers.

      It will be able to calculate tip speed using the various gear ratios
      available and give a Mach number for any given altitude. (Mach varies
      with altitude, so a prop that works well on the ground may go
      transonic at 10,000 feet).

      Then there is the question of efficiency. This is a tough one to
      estimate. Momentum theory tells us that the most efficient
      propulsion system is one that accelerates a large diameter
      stream tube to a speed only a little faster than the airplane. See
      the attached graphics "Efficiency Fundamentals" and "Thrust
      Equation." (Btw, the"m" with a dot on top, or mdot, denotes mass
      flow rate, which is equal to air density times velocity times area;
      mdot = rho * V * A).

      Obviously we want our prop to be as large diameter as possible
      without going into transonic range which will kill the thrust. Since
      tip speed is a function of both rotational speed and translational
      speed (the speed of the aircraft) -- as well as the gear reduction,
      prop diameter and rpm -- the goal is to find the most efficient prop
      diameter within those constraints.

      Advance ratio is a key efficiency metric, but it varies with speed.
      So a fixed pitch prop (or ground adjustable) cannot provide an
      optimal advance ratio in all flight regimes. However the
      spreadsheet should be able to give us some input on the optimal
      advance ratio for the speed and prop size selected.

      The guy from Powerfin seems to have diagnosed the problem that was
      mentioned above -- namely that there was a negative angle of attack
      at high airplane speed on the inboard span of the prop. We can see
      this explained in the graphic "Advance Ratio."

      The diagram illustrates the same prop section at the same rotational
      speed but at two different airspeeds. The one on the right shows the
      negative angle of attack and hence negative lift with a high
      airspeed. This is why the Europa hit a "brick wall" at 150 mph, and
      then went 25 mph faster with the right prop.

      It's really a pain when things like that happen, so I think we can
      come up with a spreadsheet that will at least help us get in the
      right ballpark with prop sizing.

      Regards,

      Gordon.


Gordon, you will find some very good prop spread sheets in some of
these zip files. Particularly John Ronz and Bill Freeman.

Also QB zip is a very nice integrated BASIC development
environment Smart-editor/interpreter/compiler that will run on the
command line in Windows. Place it in a folder named QB and  unzip
it. Select "Run" and type "Command" That puts you in DOS. Then use
the DOS change directory command until you find QB. Get in the QB
directory and type "QB" and press return while still in the command
line mode. There are a wealth of QB prop programs
in the zip files. Particularly the ones written by Vance and Ed Dokus
over many years. I'll send that QB zip file in the next message as
it is about 800K

Paul Lamar ...No rotor no motor.


OK Gordon here is  QB.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.