Paul, here are few pictures from my new muffler construction. The
flange has two stubs with slip joints 0.065 SS that are pulled
together with strong springs (not shown). The perforated tube is
welded only on one side to the can. The other side fits into a slip
socket welded to the lid, so it is allowed to float. Sofar works
very well , but I need more time to see how it will hold?
Bulent.
I assume that is 321 SS. Nice workmanship.
I hate to be the bearer of bad news but the perforated tube
will run white hot, melt and eventually puke it self out of the
can and out the through the prop. Tom Jordon had something like that
on a Limo EZ. One could stand behind the prop with the engine
at full chat and look down the exhaust pipe. It was like
looking at a very bright light bulb in there :)
Try to get some sort of air cooling tube down the center.
I'll send some 3D's shortly.
Also put some sort of safety strap on the whole muffler
so if worse comes to worse the whole muffler won't go through
the prop taking out a blade.
Paul Lamar ...No rotor no motor.
-----------------------
I was involved in the Exhaust industry for a number of years including
designing the odd muffler.
What Paul says is true, however the one thing not mentioned is just how
bad this style of design is
it will allow exhaust gas flow that's about it, this is what is
nicknamed a "back pressure" it is
unbelievably bad in gas flow which = HP which means increased fuel
consumption by quite a bit,
My suggestion is do not use this style design at all. It is one of the
worst designs there is.
It will shut things up but , it will run a lot hotter, create excessive
back pressure, increase fuel
consumption & reduce horsepower just to name a few things all of which
you really do not want!
Sorry. I just had to stress this.
Try another style. While not the best option it will work somewhat
better if you use the can with out the tube
in the middle try to improve the tube curve into it, and use the pipe
out it bigger the better within limits in the
same place, while not the most efficient it is better than with the
perforated tube in the middle it will also last a while
and yes use at least 2 or more support straps to stabilise it and to
ensure if it breaks it stays right there you
will hear it if it breaks.
Regards David
You must use extreme caution testing experimental mufflers on pushers.
I don't remember the details now but I think Joe Hull had a problem with
the muffler on his Cozy. If he's on this list maybe he can refresh our
collective memory.
Is there some way to capture all the parts that might shed and go
through the pusher prop? That must be part of the design.
I just use the stock 2nd gen cast iron manifold, bulletproof, not that
loud, not that much excess weight, no problems in 650+ hours of flying
over the last 7+ years.
Perry
Joe caught it before it broke off completely.
Needed some support links for the weight of the can back and
up to the engine block. Perry uses the one on the left in
the second pic.
Paul Lamar ...No rotor no motor.
"> Exhaust - I was on my way to OSH and about an hour east of Cheyenne,
> Wyoming, over Nebraska when I felt a slight change in the vibration of the
> airplane. All the temps, pressures and RPM were fine - just a slight
> change
> in the vibration. So I figured I better get on the ground and see what was
> up. I landed at a little ranching town (population 267) with a 4000ft
> runway
> (since I need lots of runway to land) and after landing and running up the
> engine - the engine quit DEAD. The paint on the cowling started to bubble
> and burn - not good. I pulled the cowling and found that the big tube of
> the tangential muffler had broken off both of the 2" runners that come off
> the exhaust flange. The hot exhaust had melted the wires together to the
> injectors and other wires in that area - that's why the engine quit."
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.