Subject: Source for minerature regulator? Cheap EFI?
From: Rotary Engine
Date: 2/10/2007, 6:17 PM
To: AARotary Engine



    > I plan on experimenting with the low pressure dribble fuel injection
    > system. I have the pix of the 1/8" miniature regulator you shared
   with
    > the list. I found what looks like the one you mentioned at McMaster
    > Carr
    > (# 6763K11), but it is the relieving style so it vents if the
    > regulated
    > side exceeds the selected pressure. NOT GOOD for fuel to be vented!
    >
    > Can you tell me the source for the regulator in the pix?
    >
    > Doc Custer
    > Retired Software Engineer and sometime Audiologist
    >
    > It is this little jewel right Doc?
    > It has three pipe threaded ports so you plumb the return flow
    > back to the fuel tank exactly what must be done using
    > Tracy's EFI system. The only ones that don't do this are the
    > computer controlled PWM fuel pumps.
    >
    > ---------------------------------------
    >
    > This message triggered an idea Doc. A combination of
    > EFI and the low pressure dribble system. Since one needs
    > a low pressure electric fuel pump no matter what control the pump
    > pressure PWM
    >
    > (Assuming electric fuel pump for 13B?) Yes and all low wing
    > airplanes.
    >
    > with a 44 cent
    > PIC microcomputer that takes data in
    > from a MAP sensor,
    >
    > (Manifold Air press-what sensor is used/specified?). Free Scale.
    >
    > RPM and a leaning knob pot on the instrument
    > panel.
    >
    > To quote Don Lancaster:
    > "The PIC microprocessor from Microchip Technology has now
    > become the hardware component of the decade. To the point
    > where it is laughingly absurd to ever again use a 555 timer."
    >
    >
    > Voila!!! Super simple low pressure EFI!!!! The PIC has an A to D
    > for the MAP sensor and leaning knob and an interrupt
    > for the RPM. Should take all of an hour to write the BASIC
    > program :)
    >
    > (leaning knob interface is mechanical or analog sensor
    > with A/D to PIC? Yes
    >
    > Potentiometer? Variable resister.
    >
    > Is this all written in "BASIC"? Can be.
    >
    > If so a good book to learn BASIC - No, I never did
    > learn it. It varies with the version. The docs come
    > with the language program.
    >
    > No injectors. Small holes in the p-port slide throttle
    > instead.
    >
    > This is the slide throttle outlined/depicted on your
    > website, right? Correct.
    >
    > No injector wires in the cowl to burn. Only wires go
    > to the low cost, low pressure, off the shelf fuel pump.
    > No leaning needle valve. No metering ramp in the slide throttle
    > or multiple holes. Just one small hose
    >
    > So the drawing on the website will change??? Correct.
    >
    > There is a small hose to the MAP sensor
    >
    > is this an analog transducer of some sort?? Correct
    >
    > mounted on the PIC PC board which
    > is just behind the panel with the PC board mounted leaning
    > pot shaft sticking through the panel.
    >
    > If you want to spend a bit more than 44 cents on the PIC
    >
    > is this an electronic board with I/O? No. The I/O is on
    > the chip.
    >
    > 44cents??? Just for the chip.
    >
    > you can
    > add a USB data acquisition interface and download the flash stored
    > historical data to a PC. Since THE pic knows the fuel flow it knows
    > the GPH. Since the PIC knows the GPH and it could take NEMA 0183
    > ASCII data in from a GPS and calculate and display the MPG IN
    > REAL TIME!!!!
    >
    > Handy for checking winds aloft.
    >
    > Now if you add the clutch throw out bearing dyno you could
    > display REAL TIME HP and BSFC.
    >
    > Ive read the website and still don't know what this means?
    >
    >
    > Tracy should be doing this anyway
    > since he is building both the PSRU and the EFI.
    >
    > This is probably the best idea I have had in the last
    > couple of years if I do say so myself :)
    >
    > BTW Sorry corporation. You can't patent it as I have
    > published it here first.
    >
    > Paul Lamar ...No rotor no motor.
    >
    >
    >
    > Ok guys. I know I need to read SOMETHING X 4 to just get a clue about
    > what you are discussing here. Please refer me to what I must
   read/study
    > to understand some/most of what's written below. I know a little
    > programming as I did some PLC programming in the 80's and early 90's.
    > (That's what getting promoted to management does for one's technical
    > skills). I have never been an automotive type (read engines). So any
    > help with some general understanding and roadmaps to in depth
   (not too
    > deep please) study of the EFI system(s) specifically for the rotoray
    > engine in "our" aeronautical application. I rebuilt a Dodge slant six
    > in my 1975 pickup because I couldn't afford to do anything else. I've
    > built lots of "things". Homes, apartments, strip centers,
   sailboats and
    > control systems for chemical plants and refineries, so I can
   understand
    > the above average technical jargon given the available reference
    > material. I understand A to D and boolean logic although some of the
    > symbols in your attachment are new (or did I just forget?) to me. ANY
    > help would be appreciated as I need to be able to understand this
    > stuff. I've also made notations in the text below as to what I
   know and
    > what I don't. I'm also a member of the "Glass Panel Group"
    > http://groups.yahoo.com/group/GlassPanel/ where I'm trying to
   learn how
    > to build my own "GPS Moving Map" and other stuff.
    >
    > Allen Slominski
    > Houston, TX
    > (Uneducated and Thirsty for Knowledge)
    >
    > We will start with a glossary.
    > PIC Very cheap single chip microcomputer from Microchip Inc.
    >
    > GPH: Gallons Per Hour.
    >
    > MAP: Manifold Air Pressure. No air zero power. 30 inches of
    > Hg full power.
    >
    > EFI: Electronic Fuel Injection. Now standard on all cars.
    >
    > BSFC: Brake Specific Fuel Consumption. A measure of how much
    > HP is generated in one hour per pound of fuel burned in one hour.
    > A gallon weighs six pounds.
    >
    > ASCII: data. American Society ???? I forgot. All the letters
    > of the alphabet and the numbers 0 to 9. Basically what you
    > have on your keyboard. There are standard binary codes assigned
    > to each letter or number. ASCII data is human readable as opposed
    > to ones and zeros computer data.
    >
    > PWM: Pulse Width Modulation. A means of controlling the
    > speed of an electric motor. The wider the pulse the
    > more juice the motor gets and the faster it goes.
    > the number of pulses per second have nothing to do
    > with it other than making it seem smoother.
    >
    > MPH: Miles Per Hour.
    >
    > GPS: Global Position Satellite
    >
    > NEMA 0183: National Electronic Marine Association a standard means
    > of having GPS's talk to other devices like auto pilots
    > and personal computers through just 3 wires called an RS232
    > serial interface. The data comes out in ASCII form
    > and in a specified order. Time first, MPH second, Latitude third,
    > etc., etc., etc..
    >
    > BASIC: Simple programming language. Can be written in BASIC
    > as there are BASIC compilers and interpreters for the PIC.
    >
    > REAL TIME: Happening as we speak. In other words if you talk
    > to your computer and the computer understands some how and
    > the words appear on the screen immediately as you are speaking
    > then that is real time. If it happens several minutes later that
    > is not Real Time. If the PIC is connected to a PC and the fuel
    > pump motor pulse width, the engine RPM and the manifold pressure
    > data comes out in a continuous stream from a USB port then that
    > is Real Time.
    >
    > POT: A variable resistor or potentiometer.
    >
    > A/D: Analog to Digital converter. A leaning potentiometer
    > has three wires. The top wire is connected to five volts
    > the bottom wire is connected to ground. The center wire
    > contacts the resistor some where along its length. As you
    > turn the shaft some voltage between zero to five volts
    > is seen on that 3rd wire. That is called analog data.
    > An 8 bit A/D converts that analog data to a binary number
    > between zero and 256.
    >
    > Clutch throw out bearing dyno: A method of measuring the
    > torque on a helical gear set using an annular hydraulic cylinder
    > that surrounds the input shaft to a PSRU. Annular hydraulic
    > cylinders are widely used in passenger cars and truck to throw
    > the clutch out of engagement (Invented by me 35 years ago:))
    > If you know the torque and the RPM you know the horsepower.
    > Use the search function in your email program to search
    > old messages for more info on this subject. You have been
    > saving them have you not? :)
    >
    > Did I miss anything? Any more questions along these lines?
    > Google is also a big help on this stuff.
    >
    > There is a magazine at some book stores called Nut & Volts.
    > Great for learning about this sort of PIC stuff.
    >
    > Paul Lamar ...No rotor no motor.

   ASCII: American Standard Code for Information Interchange. Catchy,
   huh? :)

   Doc Custer
   Retired Software Engineer and sometime Audiologist

   Thanks Doc

   --
   Paul Lamar ...No rotor no motor.


Gentlemen, thank you.  I am in your debt.

Allen Slominski
Houston, TX



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2007 All world wide rights reserved.