Subject: EFI block I/O diagram
From: Rotary Engine
Date: 2/20/2007, 5:13 PM
To: AARotary Engine


    Attached is the Input-Output block diagram for the simple EFI system.
    This diagram is intended to discover any missing sensors or engine
    outputs (i.e., other than for pilot information).

    Please comment, especially omissions. I would rather provide for a
    sensor up front rather than have to patch or edit the code later on. I
    realize that not everyone will want all the sensors.

    Fuel flow can be calculated from the fuel pressure given a calibrated
    hole in the slide throttle. The two pumps on each side (tank?) can be
    operated in parallel, i.e., both on all the time; in the event one
    fails, the uC can notify the pilot and increase the duty cycle of the
    remaining good pump in order to maintain proper fuel pressure. Or, a
    switch could be provided for the pilot to switch to the other pump.
    Builders choice.

    The uC system will have total redundancy a la Tracy, i.e., an A uC and a
    B uC. If one fails, switch to the other and land.

    Doc Custer
    Retired Software Engineer and sometime Audiologist

    -----------------------------------------------------
    Looks OK to me Doc. I am glad you did that diagram.

    I am thinking out loud now.
    You can get fuel flow from the pulse width you are feeding the pumps.
    It must be calibrated because all pumps do not in general
    pump an amount of fuel directly proportional (in a linear manner)
    as a function of the the pulse width. Even tho the average voltage
    applied to the pump is directly proportional to the pulse width.

    In other words applying a 50% wide pulse to a 12 volt
    pump is the same thing as applying 6 volts DC. In any event
    you may need a voltage regulator on the 12V supply. If the battery
    is 14 volts the pump gets 7 volts.

    Another way of doing it is feeding the battery voltage to a 1/3 divider
    and feed the output of the divider to one of the A to Ds in the
    chip so the computer knows the battery voltage at all times.
    It then uses a look up table to adjust the fuel pump pulse width
    according to the available battery voltage.

      This is the cheap
    way to do it as you don't need a high power voltage regulator
    on the 12 volt supply. If the battery voltage is low you widen
    the pulse to compensate. Pumps can take up to 7 or 10 amps and as far
    as I know there are no  single chips regulators that will handle
    that. Well at least the last time I looked. In any event you can
    display the battery voltage on the instrument panel as a trouble
    shooting aid.

    The other possibility is to ignore the voltage level as most
    alternators have a regulator that is pretty much set to 13.5 or 14
    volts or so. Assume that will always put you in the mixture ball
    park and the pilot in the loop will fine tune with the leaning knob.

    The EGT is a bit hard to use as a feed back sensor as the response
    time is very slow and
    it changes direction as you pass through peak EGT. You are better off
    with the O2 sensor IMHO if you are looking for a closed loop system.
    I would forget the closed loop and keep  the pilot in the leaning
    loop. The engine will run over a wide mixture range. 10:1 to 20:1.
    Air/fuel.

    EGT rises as you lean the mixture and then drops as the mixture
    gets leaner and leaner past peak. A tough nut to crack as far as
    programming is concerned. You can lean the mixture and see if it
    rises. If it rises you are on the rich side of peak EGT. If it lowers
    you are on the lean side of peak EGT. This takes a lot of time
    in addition to the slow response of the TC. .
    the only way to speed up the response of a thermal couple is
    use a smaller one. That has life limit implications.
    --
    Paul Lamar ...No rotor no motor.


Doc,

Fuel pressure alone won't give you fuel flow. You will also need to use
the MAP value. You need the pressure differential across the hole to get
your flow rate.

Do you plan to use any barometric compensation?

Ken Bauman


Good point Ken Bauman about the pressure differential, especially in a low
to moderate pressure system.

I hadn't considered barometric compensation as I assumed manifold pressure
would suffice. Is this wrong?

Doc Custer
Retired Software Engineer and sometime Audiologist

We can simulate it by pulling a vacuum on a glass jar and see
how long it takes to inject X amount of fuel at Y pulse width.
I have an electric vacuum pump.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.