Subject: EFI block I/O diagram
From: Rotary Engine
Date: 2/20/2007, 9:54 PM
To: AARotary Engine


    >     Attached is the Input-Output block diagram for the simple EFI
   system.
    >     This diagram is intended to discover any missing sensors or
   engine
    >     outputs (i.e., other than for pilot information).
    >
    >     Please comment, especially omissions. I would rather provide
   for a
    >     sensor up front rather than have to patch or edit the code
   later on. I
    >     realize that not everyone will want all the sensors.
    >
    >     Fuel flow can be calculated from the fuel pressure given a
   calibrated
    >     hole in the slide throttle. The two pumps on each side
   (tank?) can be
    >     operated in parallel, i.e., both on all the time; in the
   event one
    >     fails, the uC can notify the pilot and increase the duty
   cycle of the
    >     remaining good pump in order to maintain proper fuel
   pressure. Or, a
    >     switch could be provided for the pilot to switch to the other
   pump.
    >     Builders choice.
    >
    >     The uC system will have total redundancy a la Tracy, i.e., an
   A uC and
    > a
    >     B uC. If one fails, switch to the other and land.
    >
    >     Doc Custer
    >     Retired Software Engineer and sometime Audiologist
    >
    >     -----------------------------------------------------
    >     Looks OK to me Doc. I am glad you did that diagram.
    >
    >     I am thinking out loud now.
    >     You can get fuel flow from the pulse width you are feeding
   the pumps.
    >     It must be calibrated because all pumps do not in general
    >     pump an amount of fuel directly proportional (in a linear
   manner)
    >     as a function of the the pulse width. Even tho the average
   voltage
    >     applied to the pump is directly proportional to the pulse width.
    >
    >     In other words applying a 50% wide pulse to a 12 volt
    >     pump is the same thing as applying 6 volts DC. In any event
    >     you may need a voltage regulator on the 12V supply. If the
   battery
    >     is 14 volts the pump gets 7 volts.
    >
    >     Another way of doing it is feeding the battery voltage to a 1/3
    > divider
    >     and feed the output of the divider to one of the A to Ds in the
    >     chip so the computer knows the battery voltage at all times.
    >     It then uses a look up table to adjust the fuel pump pulse width
    >     according to the available battery voltage.
    >
    >       This is the cheap
    >     way to do it as you don't need a high power voltage regulator
    >     on the 12 volt supply. If the battery voltage is low you widen
    >     the pulse to compensate. Pumps can take up to 7 or 10 amps
   and as far
    >     as I know there are no  single chips regulators that will handle
    >     that. Well at least the last time I looked. In any event you can
    >     display the battery voltage on the instrument panel as a trouble
    >     shooting aid.
    >
    >     The other possibility is to ignore the voltage level as most
    >     alternators have a regulator that is pretty much set to 13.5
   or 14
    >     volts or so. Assume that will always put you in the mixture ball
    >     park and the pilot in the loop will fine tune with the
   leaning knob.
    >
    >     The EGT is a bit hard to use as a feed back sensor as the
   response
    >     time is very slow and
    >     it changes direction as you pass through peak EGT. You are
   better off
    >     with the O2 sensor IMHO if you are looking for a closed loop
   system.
    >     I would forget the closed loop and keep  the pilot in the
   leaning
    >     loop. The engine will run over a wide mixture range. 10:1 to
   20:1.
    >     Air/fuel.
    >
    >     EGT rises as you lean the mixture and then drops as the mixture
    >     gets leaner and leaner past peak. A tough nut to crack as far as
    >     programming is concerned. You can lean the mixture and see if it
    >     rises. If it rises you are on the rich side of peak EGT. If
   it lowers
    >     you are on the lean side of peak EGT. This takes a lot of time
    >     in addition to the slow response of the TC. .
    >     the only way to speed up the response of a thermal couple is
    >     use a smaller one. That has life limit implications.
    >     --
    >     Paul Lamar ...No rotor no motor.
    >
    >
    > Doc,
    >
    > Fuel pressure alone won't give you fuel flow. You will also need
   to use
    > the MAP value. You need the pressure differential across the hole
   to get
    > your flow rate.
    >
    > Do you plan to use any barometric compensation?
    >
    > Ken Bauman
    >

   Good point Ken Bauman about the pressure differential, especially in
   a low
   to moderate pressure system.

   I hadn't considered barometric compensation as I assumed manifold
   pressure
   would suffice. Is this wrong?

   Doc Custer
   Retired Software Engineer and sometime Audiologist

   We can simulate it by pulling a vacuum on a glass jar and see
   how long it takes to inject X amount of fuel at Y pulse width.
   I have an electric vacuum pump.

   Paul Lamar


Took this from an old MegaSquirt posting.


> > I am totally confused here. My experience with reciprocating
aircraft
> > engines climbing to altitude is that it gets leaned out, both
carb and FI.
>
> (Yeah, I know. A bunch of you are thinking "here we go again," but
I've done
> this often enough that I think I can answer the question
satisfactorily in a
> single e-mail.)
>
> Imagine an engine with constant VE, it's 100% across the tables.
We only
> run this engine at 70f, so the only variable is manifold absolute
pressure.
>
> Throttle the engine to 50 kPa at sea level with an ambient pressure
of 100 kPa,
> and pulse with is, for example, 5.0 ms. Now fly up to 5000 feet,
ambient
> pressure drops to 84 kPa and make sure we are still throttled to 50
kPa in
> the manifold. What is our pulsewidth now? Correct, it is _still_
5.0 ms.
> Change to any altitude you want, but as long as you have a MAP of
50 kPa,
> the PW is 5.0.
>
> Well, this is only taking into account the intake side of the
engine! In
> a real engine, the volumetric efficiency is not dictated solely by
the intake
> tract, but also by the exhaust system (headers, cam timing, exhaust
valve
> size and all that can change the power output/VE, right?).
>
> Imagine we are running the engine in a dyno cell ambient 100 kPa,
50 kPa of
> MAP, resulting VE = 100% and we get that 5.0 ms PW. Now put a
vacuum cleaner
> on the end of the exhaust pipe, and pull it down so that the
exhaust system
> is under a perfect vacuum (extreme case, but gets the point
across). The
> VE magically goes way up, because we've got a super extractor
exhaust now.
> Suddenly the engine goes lean, because the VE went up, but we
didn't know
> it inside MS because we only measure MAP, not the ambient pressure
at the
> exhaust outlet!
>
> This is _exactly_ what happens as you gain altitude. The MAP
sensor corrects
> the fuel pulse based on MAP, so altitude changes are of no
consequence here,
> but MS has no way of knowing what is going on in the exhaust system.
>
> Here's the bottom line:
>
> Barometric correction ENRICHS the mixture as you gain altitude to
correct
> for the increasing efficiency of the exhaust system.

Ken

Interesting. Looks like we need another pressure sensor.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.