Paul,
I missed the post that started all of this. Could you
resend it
to me?
I'm looking to understand the mechanical layout of this
EFI and the
theory behind it.
Thanks
Ken Bauman
> Is it possible to reverse the direction the slide throttle
travels
> with the use of a bell crank? Jerry
Jerry,
If you reverse the slide throttle you can make the housing 2"
shorter.
IMHO It is much better to provide attachment of the
throttle cable
directly to the slide throttle compared to building some
extra
bracket.
As you push the throttle control forward the throttle plate
actually moves forward opening the intake.
Take a look at the AeroCarb to get the picture.
http://www.aeroconversions.com/carb_index.html
I have one of these on one of my planes and it works great.
They even make a ninety degree bellcrank for some
installations
which also is to be mounted directly to the throttle body. I
modified the bellcarnk to allow 85mm (3 3/8") of throttle
cable
travel for the 29mm of throttle plate travel. jm2c
Terry Adams
This is a VERY simple system. No computer, no sensors, no
floats, no venturi, no fuel injectors, no nothing. Just very
low pressure fuel. The fuel orifice area simply increases
with
the air passage area increase. Bigger fuel hole bigger air
hole.
There is another simple series valve that controls leaning.
I think I have figured out how to do this with our slide
throttle. No fuel injectors required. In fact other than
a bit of plumbing there are no additional parts.
Patent applied for :)
Paul Lamar
This is a VERY simple system. No computer, no
sensors, no
floats, no venturi, no fuel injectors, no nothing.
Just very
low pressure fuel. The fuel orifice area simply
increases
with
the air passage area increase. Bigger fuel hole bigger
air hole.
There is another simple series valve that controls
leaning.
Paul Lamar
snips ................
Times up.
Here it is. Super simple. A series of progressively larger
feed holes in the Teflon slide communicating a with a fixed
larger fuel hole in the aluminum spacer.
Patent applied for :)
--
Paul Lamar ...No rotor no motor.
This is part of what I needed. I went back and read all the
posts I had
skipped due to the "cheap regulator" heading. I'll pay more
attention.
Months ago I mentioned using two high pressure pumps (PWM) and
some CIS
injectors as a simple EFI. Using a low pressure pump in a
dribble system
seems that the fuel would not have good delivery or
atomization. Airflow
Performance has some nice mechanical injectors that work at
around 5lbs
psi.
High pressure fuel resists vapor lock better.
If you monitor the pressure differential across the injector
you can
compensate for pump wear, battery voltage etc.
Ken Bauman
Could be your post was in my subconsciouses mind Ken.
Do you recall about what month and year? I'll search back for
it.
Paul Lamar
12/6/06 therabouts.
I'm not even sure it I didn't hear it somewhere before. I've kicked it
out a number of times on different lists. I like the idea of it being in
the public domain. Garfield once chewed my ass about stuff needing to be
patented to protect aviation from corporate greed.
Hope to see any variation run. I've been gathering components to play
with a CIS version. I have the injectors, pump and a PWM for manual
control of the pump. I plan to just turn up the pressure as I increase
RPM to see if I can do it. If that worked then go from there.
Doc's sounds better.
Ken Bauman
Didn't Garfield die?
A patent is not worth the paper it is printed on unless
you have millions to fight corporations that steal it.
Been there done that.
--
Paul Lamar ...No rotor no motor.
He is gone, this was a while back. This concept has been kicking
around for a while.
Ken
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.