> Paul,
>
> Thanks for the info on Microchip.
>
> In the six weeks I was away did you find a way to use the constant spray
> slide throttle system with a turbo charged engine? I checked out your
> latest drawings on the website. Correct me if I am wrong but it appears
the
> latest configurations is quite an improvement over the gravity flow
system
> and if I am not mistaken it is a low pressure electronic fuel flow
> controller.
>
> You probably had lots of discussions about this design but something
Matt
> just commented on makes me wonder why the need of a pressure regulator.
A
> small pressure tank with an internal diaphragm to dampen out the pulses
I
> can understand.
>
> Let me see if I got this right.
>
> If the throttle is opened, more holes are uncovered and fuel pressure
must
> drop. The fuel pressure sensor then responds by having the duty cycle of
the
> pump increased to maintain the required flow pressure. Since we can only
> push so much fuel through a little hole and pressure will increase
faster
> than flow, fuel flow is tied to throttle setting and how many holes
> (injectors) are open at the time.
>
> If that is the case then changing the duty cycle by tweaking the fuel
> pressure control would act as a leaning mechanism right?
>
> It seems we are trying to control flow where controlling pressure
through
> what are basically will be a series of optimum shaped injectors might
> accomplish the same aim?
>
> Doug Fir
>
>
> On the constant dribble, super simple, all mechanical system
> Doug suggested using the knob on the pressure regulator
> to lean the engine. That in theory allows doing away with the leaning
> needle valves. Here is a 3D on that system.
> The pressure would have to be increased and the holes made
> smaller so one would get a wider ranges of fuel flows.
> Good idea Doug. I am not sure you would get a wide enough range
> but a bench test should prove that one way or another.
>
>
> --
> Paul Lamar ...No rotor no motor.
Paul,
Thanks for the compliment, however I was suggesting you change the
pressure
by changing the duty cycle on the pumps. There are several ways to do that
One would be to fool the microprocessor by influencing the fuel pressure
sender output.
I don't think you would want to use a pressure regulator like you have
shown
in the picture. What you in hand appears to be a pressure regulator for
air
or gases. It has a plastic case, with a rubber diaphragm and a spring
inside. You wouldn't want that in your system and definitely not your
cockpit because they are not robust.
About the optimum hole size, yes it needs testing. The beauty of your
present idea is that you can optimize the holes to shape them like
nozzles.
For example a larger bore cumulating in a tiny hole. All the bores in your
throttle could be the same but only the final nozzle hole could be
different
sizes if testing warranted it.
IMHO Creating a long sealed fuel cavity within the AL 1/4" thick slide
throttle casing is the bigger challenge at the moment. I am thinking about
a
solution though.
Doug Fir
It is a nylon piston and not a rubber diaphragm. You are
right it is air but they say it will also work with
certain fluids. I intended soaking it in fuel to see what
would happen.
On the Holley gerotor positive displacement fuel pumps the
pressure regulator is built in and the injector hole is probably
large enough to not increase the pressure significantly when
the pump speed and flow is increased. I intend getting one and
bench testing it to calibrate the flow verses pulse width
unless Doc does it first.
I am pretty well sold on the PICAXE approach as apposed
to the purely mechanical approach because of
the potential glass cockpit advantages. Besides it is a super
simple system and fast and easy to program yourself BASIC.
A few years ago real time BASIC compiler programed EFI system
would be out of the question but technology marches on with
faster and faster processors and more and more memory. The
cost of flash memory has also dropped enormously.
BTW Soon portable computers will no longer have disk drives.
Just 100 gig flash memory and will be the size of a pack of
cigarettes. Virtual qwerty keyboards will be projected on the
desk surface in front of you and the virtual display projected
on the wall in back of your desk. Such a keyboard is already
available. The display will show up any day now. I have a
clock that projects the time on the ceiling already.
Paul Lamar ...No rotor no motor.
Paul,
I have been to the Cubloc site as well as the PICAXE sites and I think these
devices and boards have unbelieveable potential. Which PICAXE starter setup
did you think was best. I would like to start with and engine monitor and
then maybe flight data. If you look at the related sites they have
thermocouple, pressure, and accelerometer sensor interfaces to these PICs!
Any suggestions?
Thanks
Joe Berki
Limo EZ, finsihing the firewall and will start to disassemble the 13bs
I have not investigated the Cubloc site. The PICAXE is getting
the most buzz.
Looks like we will need the 40 pin chip at the rate we are
adding sensors :)
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.