Subject: EFI block I/O diagram
From: Rotary Engine
Date: 2/21/2007, 9:23 AM
To: AARotary Engine


     >     Attached is the Input-Output block diagram for the simple EFI
    system.
     >     This diagram is intended to discover any missing sensors or
    engine
     >     outputs (i.e., other than for pilot information).
     >
     >     Please comment, especially omissions. I would rather provide
    for a
     >     sensor up front rather than have to patch or edit the code
    later on. I
     >     realize that not everyone will want all the sensors.
     >
     >     Fuel flow can be calculated from the fuel pressure given a
    calibrated
     >     hole in the slide throttle. The two pumps on each side
    (tank?) can be
     >     operated in parallel, i.e., both on all the time; in the
    event one
     >     fails, the uC can notify the pilot and increase the duty
    cycle of the
     >     remaining good pump in order to maintain proper fuel
    pressure. Or, a
     >     switch could be provided for the pilot to switch to the other
    pump.
     >     Builders choice.
     >
     >     The uC system will have total redundancy a la Tracy, i.e., an
    A uC and
     > a
     >     B uC. If one fails, switch to the other and land.
     >
     >     Doc Custer
     >     Retired Software Engineer and sometime Audiologist
     >
     >     -----------------------------------------------------
     >     Looks OK to me Doc. I am glad you did that diagram.
     >
     >     I am thinking out loud now.
     >     You can get fuel flow from the pulse width you are feeding
    the pumps.
     >     It must be calibrated because all pumps do not in general
     >     pump an amount of fuel directly proportional (in a linear
    manner)
     >     as a function of the the pulse width. Even tho the average
    voltage
     >     applied to the pump is directly proportional to the pulse width.
     >
     >     In other words applying a 50% wide pulse to a 12 volt
     >     pump is the same thing as applying 6 volts DC. In any event
     >     you may need a voltage regulator on the 12V supply. If the
    battery
     >     is 14 volts the pump gets 7 volts.
     >
     >     Another way of doing it is feeding the battery voltage to a 1/3
     > divider
     >     and feed the output of the divider to one of the A to Ds in the
     >     chip so the computer knows the battery voltage at all times.
     >     It then uses a look up table to adjust the fuel pump pulse width
     >     according to the available battery voltage.
     >
     >       This is the cheap
     >     way to do it as you don't need a high power voltage regulator
     >     on the 12 volt supply. If the battery voltage is low you widen
     >     the pulse to compensate. Pumps can take up to 7 or 10 amps
    and as far
     >     as I know there are no  single chips regulators that will handle
     >     that. Well at least the last time I looked. In any event you can
     >     display the battery voltage on the instrument panel as a trouble
     >     shooting aid.
     >
     >     The other possibility is to ignore the voltage level as most
     >     alternators have a regulator that is pretty much set to 13.5
    or 14
     >     volts or so. Assume that will always put you in the mixture ball
     >     park and the pilot in the loop will fine tune with the
    leaning knob.
     >
     >     The EGT is a bit hard to use as a feed back sensor as the
    response
     >     time is very slow and
     >     it changes direction as you pass through peak EGT. You are
    better off
     >     with the O2 sensor IMHO if you are looking for a closed loop
    system.
     >     I would forget the closed loop and keep  the pilot in the
    leaning
     >     loop. The engine will run over a wide mixture range. 10:1 to
    20:1.
     >     Air/fuel.
     >
     >     EGT rises as you lean the mixture and then drops as the mixture
     >     gets leaner and leaner past peak. A tough nut to crack as far as
     >     programming is concerned. You can lean the mixture and see if it
     >     rises. If it rises you are on the rich side of peak EGT. If
    it lowers
     >     you are on the lean side of peak EGT. This takes a lot of time
     >     in addition to the slow response of the TC. .
     >     the only way to speed up the response of a thermal couple is
     >     use a smaller one. That has life limit implications.
     >     --
     >     Paul Lamar ...No rotor no motor.
     >
     >
     > Doc,
     >
     > Fuel pressure alone won't give you fuel flow. You will also need
    to use
     > the MAP value. You need the pressure differential across the hole
    to get
     > your flow rate.
     >
     > Do you plan to use any barometric compensation?
     >
     > Ken Bauman
     >

    Good point Ken Bauman about the pressure differential, especially in
    a low
    to moderate pressure system.

    I hadn't considered barometric compensation as I assumed manifold
    pressure
    would suffice. Is this wrong?

    Doc Custer
    Retired Software Engineer and sometime Audiologist

    We can simulate it by pulling a vacuum on a glass jar and see
    how long it takes to inject X amount of fuel at Y pulse width.
    I have an electric vacuum pump.

    Paul Lamar


Took this from an old MegaSquirt posting.


 > > I am totally confused here. My experience with reciprocating
aircraft
 > > engines climbing to altitude is that it gets leaned out, both
carb and FI.
 >
 > (Yeah, I know. A bunch of you are thinking "here we go again," but
I've done
 > this often enough that I think I can answer the question
satisfactorily in a
 > single e-mail.)
 >
 > Imagine an engine with constant VE, it's 100% across the tables.
We only
 > run this engine at 70f, so the only variable is manifold absolute
pressure.
 >
 > Throttle the engine to 50 kPa at sea level with an ambient pressure
of 100 kPa,
 > and pulse with is, for example, 5.0 ms. Now fly up to 5000 feet,
ambient
 > pressure drops to 84 kPa and make sure we are still throttled to 50
kPa in
 > the manifold. What is our pulsewidth now? Correct, it is _still_
5.0 ms.
 > Change to any altitude you want, but as long as you have a MAP of
50 kPa,
 > the PW is 5.0.
 >
 > Well, this is only taking into account the intake side of the
engine! In
 > a real engine, the volumetric efficiency is not dictated solely by
the intake
 > tract, but also by the exhaust system (headers, cam timing, exhaust
valve
 > size and all that can change the power output/VE, right?).
 >
 > Imagine we are running the engine in a dyno cell ambient 100 kPa,
50 kPa of
 > MAP, resulting VE = 100% and we get that 5.0 ms PW. Now put a
vacuum cleaner
 > on the end of the exhaust pipe, and pull it down so that the
exhaust system
 > is under a perfect vacuum (extreme case, but gets the point
across). The
 > VE magically goes way up, because we've got a super extractor
exhaust now.
 > Suddenly the engine goes lean, because the VE went up, but we
didn't know
 > it inside MS because we only measure MAP, not the ambient pressure
at the
 > exhaust outlet!
 >
 > This is _exactly_ what happens as you gain altitude. The MAP
sensor corrects
 > the fuel pulse based on MAP, so altitude changes are of no
consequence here,
 > but MS has no way of knowing what is going on in the exhaust system.
 >
 > Here's the bottom line:
 >
 > Barometric correction ENRICHS the mixture as you gain altitude to
correct
 > for the increasing efficiency of the exhaust system.

Ken

Interesting. Looks like we need another pressure sensor.

Paul Lamar ...No rotor no motor.

I agree. Thanks Ken.

Attached is the latest diagram.

Doc Custer
Retired Software Engineer and sometime Audiologist


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.