Subject: Aluminum center/end plate ? Cheap bell housing.
From: Rotary Engine
Date: 2/22/2007, 4:26 PM
To: AARotary Engine


 > > Paul: You, any one else, ever look at RB's aluminum end and center
 > housings
 > > and wonder how much trouble to machine out of solid aluminum
 billets
 > for
 > > PPort engines? After all, they won't need intake ports in them.
 > > jofarr, soddy tn
 > >
 > > Can't be done because they are hollow. Now if somebody invented
 > > a tiny robot milling machine that you could put down a small hole
 > > and have it mine out cavities in the material that would work.
 > >
 > > No intake ports would certainly help.
 > >
 > > If you made them in two pieces that would also work if you could
 > > figure out a way to seal the internal joints. Could be done with
 > > some sort of gasket or O-rings and that is exactly what Richard
 > > Sohn is working on.
 > >
 > > Paul Lamar ...No rotor no motor.
 > >
 > > Paul,
 > > Those two pieces could easily be furnace brazed together.
 According to
 > > Alan Tolle Everett even did a steel 2 piece milled and furnace
 brazed.
 > > For the "superlite" engine. For aluminum the problem remains the
 > coating.
 > > I'm convinced that it would be "do able" just expensive. I
 think that
 > the
 > > state of milling equipment probably do a better and faster job
 than
 > > casting.
 > > Bill Jepson
 >
 > > hi Bill, this is the way my machinist and i have planned to do
 it. what
 > > would you estimate the cost of casting them? just so i could
 compare
 > costs.
 > >thanks , wyo. walt.
 >
 > Walt
 > The problem is the cost of the pattern making. You could easily
 spend 10K
 > to 15K setting up the patterns to cast the various parts. That
 is before
 > making a single casting. Additionally the sad thing is you could find
 > that your
 > casting still didn't work due to porosity or core shift. The fact is
 > that billet
 > construction would probably be cheaper until at least the 100
 unit mark.
 > machining from billet you have a reasonable expectation that your
 first
 > part
 > would work. All the aluminum concerns about coating are about the
 same.
 > Bill Jepson
 >
 > One possible problem I can see Bill is the compressive strength
 > of furnace braze is not as high as the base material.
 > The tension bolts put a lot of compressive stress on
 > the engine end housings.
 >
 > Paul Lamar
 >
 > Paul,
 > This is a reasonable concern, but with proper layout shouldn't be a
 > problem
 > The key is to place the braze material around the piers or in a
 center
 > reservoir
 > so the base material is in near contact. (a super thin film is
 wicked to
 > the base
 > material by heat and usually a flux) The way I've seen this done
 is to
 > weight
 > the two parts together to force out excess. Your separate wear
 surface
 > idea
 > with o-ring seals is another way to do this. (I thought that hot
 rivets
 > from
 > opposite sides could hold the plates in place) Lastly, modern
 thermally
 > conductive epoxies could be used to fasten interlocking opposite
 sides.
 > For
 > the CNC milled parts that might be the most effective method of
 all. the
 > parts could be well located and pressed together during cure. Detgun
 > coating
 > for least unwanted heat transfer. There are many ways to go after
 this, I
 > wish I had the money to pursue it. FWIW
 >
 > Bill Jepson
 >
 > JB Weld them together might work.
 >
 > Paul Lamar
 >
 > Paul,
 > If you setup the edges that come together like this, with a small
 > clearance
 > to allow the epoxy somewhere to go, it would work fine. You
 could do the
 > brazed part exactly the same way, only the clearances would change.
 > Pardon the crude model but the concept is obvious.
 > Bill Jepson
 >
 > That jpg did not work.
 >
 > Paul Lamar

 Paul,
 With the differential thermal expansion of the center plate,( two
 combustion
 chambers and cooling water between), it appears that there could be
 tension
 in any internal ribs passing from one face to the other. Any joining
 method
 would have to accommodate this.

 Colin Smith

 Possibly. Short of an FEA we would not know for sure.
 Do you have an FEA available?

 Paul Lamar ...No rotor no motor.

Does the aluminum piece have to be done in halves?

Can an iron/steel wear surface used which also bridges the openings in
the housing which allow for the machining to be done?

A one piece housing might be fairly crudely cast. Then put it through a
finish milling process to touch things up where precise tolerances are
required. Mill where the iron wear surface fits plus an o-ring groove
to seal it. Might be cheaper overall than taking huge billets of Al and
milling them out. And you might get away without gluing anything together.

Matt-

Matt,
Crude or perfect the patterns need to be done on any casting.
George (down under) did a TON of work on a bellhousing including
several iterations and everyone just kind of passed on it as being
costly with machining. I think his later versions still have a shot at
being a good solution. Took AGES to do even though George did
all the pattern work himself. (and did it well IMHO) The bellhousing
is babysteps compared to the rotary center housing. The billet method
really isn't more expensive, and if the chips bother you recycle.
The fact is that a cut housing would have better alignment and be
easy to finish. You would have to machine any casting to make it
square and flat enough to use. That machining adds to the cost of
any casting. The high pressure castings used to make things at the
factory just cost too much for us amatures. 30-40 thousand is
common. I would be glad to do SolidWorks designs of the housings
and work with someone for price considerations on the final product.
I won't hold by breath waiting for takers though. This is a serious
project, and even more difficult than meets the eye. If it was easy
several interested parties would have sold tons of them already!
Bill Jepson
PS Paul I converted that JPEG from a PDF does that matter?


Also George's Bell housing was way too heavy. The best his foundry
could do was about .25 inch thick. Speaking of that my friends
at Mazdatrix told me the way to get a cheap, light weight, high
pressure die cast bell housing is buy the whole transmission!
2nd gen transmissions are  going for $150. Buy the transmission,
disconnect the bell housing and throw the gear box part away :)

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.