Subject: Cutting P ports
From: Rotary Engine
Date: 3/31/2007, 8:37 AM
To: AARotary Engine




> > > I finished machining both housings today.  Finished up with a boring
bar
> > > slip fit 2" tube. Now all of the questions begin like JB weld or
Devcon
> > > with Al filler.  Should I alodine everything that sees epoxy? How
long
> > > should the tubes be before the slide throttle?  Can the injectors go
> > > between the slide throttle and the housing? i will try to post some
pics
> > > this weekend got to go to Arkansas for 2 days.
> > >
> > > Joe Berki
> > >
> > > P Port cutter
> > >
> > > Yes on the alodyne but do it just before you bond.
> > >
> > > The trick is to get the slide throttle as close to the
> > > engine as possible and still clear the water pump neck.
> > > See the attached 3D's. Mark S's are about 2 inches from the
> > > engine block.
> > >
> > > The electronic injectors can go just about anywhere they will
> > > fit. The constant dribble injectors position is still in debate.
> > > My latest feeling is they should go in stoves up from the
> > > exhaust manifold.
> > >
> > > -- > > > Paul Lamar ...No rotor no motor.
> >
> >
> > Paul,
> > I am planning on remote mount for the water pump but the exhaust might
get
> > in the way unless I could make the slide throttle slide toward the
> > bellhousing end.  I thought  after you alodined the surface was
protected
> > from any oxidation.
> >
> > Joe
> >
> > Sliding towards the bell housing may be a problem due
> > to the length of the slide.
> >
> > It says in the bonding prep kit that you need to bond it
> > as soon as possible.
> >
> > Here are some old 3D's on the remote mount water pump.
> > Don't got no more. All gone :)
> > -- > > Paul Lamar ...No rotor no motor.
>
> May have to build a modified slide throttle that is not as long maybe
two
> units that slide toward each other with linkage.  I thought I would use
the
> Toyota pump since all of your castings are gone.
>
> Joe Berki
>
> How much shorter does it have to be? You can take two inches
> out of the overall length by using a Teflon coated aluminum slide
> and taping it directly for the 10-32 throttle cable end.
> No round steel button in round hole in Teflon needed.
> a more expensive labor intensive way of doing it.
> Also more friction in the mechanism as the aluminum edge
> is sliding on the aluminum spacer.
>
> If you do design your own don't forget the slide must be totally
> sealed. Raw fuel accumulates in the slide and must not escape.
> It must be sucked into the engine sooner or later.
> -- > Paul Lamar ...No rotor no motor.



Has the Teflon slide been tested for sealing?

Joe

Yes. That is why I did a major redesign over the original.
The only leakage path is right around the throttle cable and
that is above the bottom of the intake tubes. Any accumulation
of fuel will run into the engine through the intake tubes.
A thin gasket is used between all the plates and the spacer.

Paul Lamar ...No rotor no motor.


Paul,
Would the fuel have to build up along the bottom of the slide until it
reached the bottom of the openings in the intake runners and Teflon?  I just
want to know if I understand this.  Also will the stove pipe  proposed for
dribble injection cause problems by connecting the intake and exhaust really
close to the ports?

Joe Berki

Yes that is the fuel level scenario.

The stove pipe is a solid rod with a short hole bored in the
top. As the cool fuel is introduced into the top cavity in
the rod it boils up into the intake runner.

There is no connection other than the heat conducted
up the rod. I need to redo this 3D and make the rods transparent
so this becomes more clear.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.