Subject: Carbon Build Up in Primary Intake Ports
From: Rotary Engine
Date: 4/7/2007, 2:17 AM
To: AARotary Engine





              Hello Paul,
              I was looking over my 20B block today and preparing to
    start the
              disassembly process when I noticed something that seemed
         unusual to me.
              Please understand that while I have quite a lot of
    experience with
              piston engines, my rotary experience is negligible.  I
    noticed that
              there was a LOT of carbon build up in the Primary Intake Ports
         while the
              smaller secondary ports were squeaky clean.  Is this normal?
         I've seen
              exhaust ports do this but usually the intake ports are
         clean.....aren't
              they???
              Don

              That is a little strange. I don't recall seeing that on
              a two rotor. I wonder the history of this particular 3 rotor.
              Perhaps it was loafed around town its entire life. Perhaps
              the turbo charger oil seal was leaking and oil was being
    sucked
         into
              the intake manifold.

              Paul Lamar ...No rotor no motor.



         Paul
         If the turbo oil was entering the intake manifold, wouldn't it
    be in the
         secondaries also?
         I've been a bit confused by this engine from the start.  Before I
         started tearing it down I wanted to
         identify exactly what I have. The last 20B I rebuilt (7 years
    ago) had
         specific identifying marks
         that distinguished the year / series. It had a stamped letter
    on the
         rotor housing next to the "Mazda 20B" marks, and that was the first
         thing I looked for.  But.....this one doesn't have that.  This
    engine
         has black on the rotor housings where is says  "Mazda 20B" and
    the batch
         number stamp isn't on there at all.  I was initially perplexed
    by this
         until I dug up some info on the Internet that suggested that it
    is an
         internal factory rebuilt engine.  I cut this info from the RX7
    forum:

         G'day from DMRH
         This is a basic way to understand your 20B engine........
         000 - 999 = 1st batch
         A000-A999= 2nd batch
         B000-B999= 3rd batch
         C000-C999= 4th batch
         D000-D999= 5th batch
         E000-E999= 6th batch (only heard of these, never seen one)

         I have never heard of an F-series. Since Mazda made just under 4000
         20B version Cosmo's I can also picture that the E-series was for
         warranty replacements if they exist at all.

         If the engine has black on the rotor housings & the batch number
         stamp isn't on there, then its an internal factory rebuilt engine.
         (meaning its been out in a car & returned after failing within the
         warranty period)

         The last engines to go into a car would have stopped around "D500"
         for fitment into a Cosmo. For example.........

         The last Cosmo sold by Mazda = JCES-100633

         However, Mazda quote selling just 369 examples of this series-II
         version so how it got to #633, I really don't understand.

         The latest Cosmo we have ever imported is JCES-100309. Its engine
         batch # D442 It was a AUG-95 car & production ceased in Sep-95.
         If you have any quiries then contact us via http://www.dmrh.com.au
         <http://www.dmrh.com.au>

         That's about all I know about it so for, but maybe it will be more
         apparent once it open it up.

         Pics of my plane and engine are at http://atexdoc.myphotoalbum.com
         <http://atexdoc.myphotoalbum.com/>
         Don

         Well if the turbo was leaking and it was only driven slowly
         then maybe the deposits were only on the secondaries. I have
         a 20B in the hangar. Next time I am out there I will take a closer
         look at the stock intake manifold and TB and see if they have a
    primary
         and secondary butterfly valve with a split plenum.
         In this picture it looks like all runners go to the same single
    plenum.

         Is the BD4 done Don? Was it flying with a AC engine and you
         are switching over to a 3 rotor?

         Paul Lamar ...No rotor no motor.


    Hey Paul,
    Those pics you attached look EXACTLY like my last 20B project.  I
    started building it for a Velocity.  I bought the Motor Mount from Al
    Gietzen after he gave up on the rotary installation for his Velocity.  I
    mounted it on a plywood firewall (2 Ply with metal between) mockup of my
    Velocity exactly like the pics.  I routed my wiring through the fire
    shield exactly like the pic.  I built an LS1 coil mount exactly like the
    one in the pics.  Painted it blue just like the pics.  Installed the
    fuel pressure bleed off system just like the pics.  I even cut Tracy's
    redrive plate at the starter mount thinking I would modify the starter
    location (but never finished that part) just like the pics.  I cut away
    a lot of the intake manifold and drilled holes in the web parts between
    the runners just like in the pics.  I made a heat shield to go between
    the intake and exhaust exactly like the pics.  It even looks like my old
    engine stand!!!  */_Damn Paul, I think that's my old engine._/*  In fact
    I'm certain if it!!!  It had a hair line crack in the rear iron housing
    where one of the top bolts held Tracy's redrive to the engine.  That
    crack always bothered me, and I thought I would eventually replace that
    housing.  What's the serial number on Tracy's RD1B redrive?  I bet if we
    checked with him, its the one he sold me.  That's a huge surprise and
    I'm happy to see it again!!!!  When I opened up that e-mail, it was like
    seeing a long lost child!!!  I had to sell it a number of years ago
    along with my entire Velocity project.  I can't remember who I sold it
    to now.  I'll have to pull out the bill of sale.  I was hurting for
    money while trying to finish my Anesthesiology Residence at Parkland
    Hospital in Dallas so I reluctantly sold it.  You wouldn't want to sell
    it would you?????

    I didn't build the BD4 I have now.  Its currently flying with a Lycoming
    IO-360 w/ Hartzell CS prop.  Not sure if I will use this current 20B for
    the BD4 or maybe another project.  I'm just fascinated with the 20B
    engine so thought I would build another one for a project.  I've been
    looking at the Foxtrot 4 and thinking about building one next year.  If
    so, I'll already have an engine ready.
    Don

    ------------------------------------------------

    It very well could have been. Someone at Sun N Fun had it for sale
    in the rotary engine work shop tent.

    Dave Leonard on here with a turbo 13B powered RV6 is an
    anesthesiologist in San Diego.

    I agree with you. The stock 20B is a fascinating engine.

    Al gave up on the rotary? That is news to me. I think you mean
    Chuck Hurlburt's Velocity. Here are some late pictures of Al's
    Velocity. Al flew in September 2006.

    Paul Lamar ...No rotor no motor.

Yes, you are right.  It was Chuck.  I corresponded with them both so
much back then that I got the names confused.  I even found our old
e-mail correspondence this evening from when we were arranging for me to
buy the motor mount.   After Chuck had the engine fire, he decided (or
his wife did) to put a certified engine in his Velocity.  That's when I
bought the motor mount from him.  Around that same time, I had been
talking with Al about his motor mount design, and if my memory serves me
correctly (which as you see, the details are a bit mixed up after 5+
years) I think Al told me about Chucks motor mount being available.

I've been looking at those pics all evening.  I'm 100000% sure its my
old engine.  I even compared them to the pics I have here at home.
Identical to the last detail!!!   I looks exactly as it did the day I
sold it.  Still mounted to the engine stand with the motor mount and
mock firewall dangling off to the side.  Next time your at the hangar,
look for the crack in the rear housing where Tracy's redrive bolts up.
If you look on Tracy's customer list in the Texas Section, you will see
my name as a past customer.  I sold that engine  back in 2002 and its
great to know that you ended up with it.

Yes, I would love to get my hands on a 3 rotor Eunos Cosmo also!!!

Don

I don't have it. I have a complete stock 20b I bought from Allen
Tolle with everything on it. As far as I know those guys in Florida
still have yours. I think they wanted $8000 for the engine, gear box
and motor mount as I recall. It showed up at Sun N Fun for at least
two years. I thought it was a bit much for the time.

The motor mount was adapted from a Franklin bed mount.
It was Chuck Harbert and not Hurlbert. Ironically both Chuck
Harbert and Joe hull bought their engines from Dave Atkins.
Here are some pictures of Chuck fire aftermath and engine.
Sorry about the quality of the pictures.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.