Subject: Carbon Build Up in Primary Intake Ports
From: Rotary Engine
Date: 4/7/2007, 6:06 PM
To: AARotary Engine



           Hello Paul,
           I was looking over my 20B block today and preparing to start the
           disassembly process when I noticed something that seemed unusual
       to me.
           Please understand that while I have quite a lot of
   experience with
           piston engines, my rotary experience is negligible.  I
   noticed that
           there was a LOT of carbon build up in the Primary Intake Ports
       while the
           smaller secondary ports were squeaky clean.  Is this
       normal?  I've seen
           exhaust ports do this but usually the intake ports are
       clean.....aren't
           they???
           Don

           That is a little strange. I don't recall seeing that on
           a two rotor. I wonder the history of this particular 3 rotor.
           Perhaps it was loafed around town its entire life. Perhaps
           the turbo charger oil seal was leaking and oil was being
   sucked into
           the intake manifold.

           Paul Lamar ...No rotor no motor.



       Paul,
       It looks like could be exhaust residue.  My 20B had exhaust port
   inserts
       with passages going back up to the intake, but I don't remember
       exactly where they terminated.  I do remember that there was a
   lot of
       buildup in them.  I removed the 20B exhaust inserts and replaced
   them
       with 13B turbo inserts.  Could this be residue from the exhaust
       recirculating back into the primary intake ports?

       Mark S.

       The purpose of that is to warm the cold side of the engine
       so the engine does not deflect into a banana shape. The flow
   goes into
       the center housing up and over to the rotor housings  down and back
       to the end housing and exhaust ports.

       This can be seen in the book Rotary engine downloaded from:
       http://www.wankel.net/~krwright/cars/rx7/manuals.html

       Everybody download both version of this book. It is the bible of the
       rotary engine.

       Paul Lamar ...No rotor no motor.


   Paul,
   I just went out to the garage and looked at an '89 6-port center
   housing.  It has an EGR valve bolted to the top.  There's a passage down
   near where the exhaust port is located on the rotor housing that leads
   up through the center housing to the EGR valve.  From the EGR valve,
   there are two small passages leading to the two primary intake ports.
   There's a thick layer of soot on all passageways.  I was thinking that
   the 20B had a similar system that would account for the buildup in the
   intake ports.  On the 20B,  I think that this passage is routed through
   the intake manifold.

   Mark S.

   Yes that is true on the 6 port  but it dumps into the primary ports
   real close to the rotor. I don't know how they do it on the 20B if they
   use EGR. I suspect the center housing is stock turbo 13B. The special
   20B intermediate housing may be a different matter. My 3 rotor
   is completely assembled so it is hard for me to tell.
   There are no manuals for the 20B in English.

   Oh I just remembered since the 20B is a turbo
   The turbo version of the 13B have the EGR blocked off
   at the top of the center housing with no EGR valve.
   See the attached picture.
   There is still EGR however on the 3rd gen 13B but it is
   done differently. The 3rd gen turbo 13B is most like a 20B.

   I am voting on a leaking turbo charger oil seal.

   Paul Lamar ...No rotor no motor.


On my 20B, the exhaust gas flows from the exhaust ports up through the
side housings and out some rectangular holes below the intake ports.
From here they go into the lower intake manifold and up to what appears
to be an EGR type valve, also attached to the lower intake manifold.
The gasses flow through the EGR (?) valve and out the rear of the lower
intake.  From there, I'm not sure where it is routed as that piece is
missing.  I'm assuming that it is routed into the upper intake just
after the tb.  Since the intake is a dual plane, it would make sense
that the gasses are plumbed to the primary side as this would be in use
at all times where the secondaries are only in operation under high
power.  Now you've got my curiosity up.

Mark S.
(It snowed today at my house here in Austin, TX.  How weird is that???)

---------------------------------------------------------------

Cannot be global warming as Texas is supposed to get hotter and
not colder.

Maybe the earth's axis is tilting and the gov. is lying to
us so we won't panic :)
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.