Subject: Experimental air craft and rotary engines.
From: Rotary Engine
Date: 4/8/2007, 4:47 PM
To: AARotary Engine



         This looks good Paul..

         More questions.. For Joe: Prior to the insulator failure, how
         recently
         had the plugs been out and inspected? From the dark color in the
pic
         posted, it doesn't appear that plug was running excessively hot.
         Hmm..

         I think it was discussed before, but I can't remember the
         answer. Was
         it predictable that the plug being used might be susceptible to
         overheating and failure (based on published heat range)?

         Maybe it should be standard practice to remove and inspect the
plugs
         after each flight for the first 10 hours?

         I can see that picking a heat range for the plugs can be a
         challenge -
         especially given the number of variables involved. For instance,
         if the
         mixture is overly rich during ground running, it might be
         interpreted
         that the heat range is acceptably cool, when in fact at high
         power the
         plug may be running too hot.

         When there is some standardization in ignition, fuel delivery,
and
         exhaust components, things are going to get easier... I wonder
what
         Powersport uses in their engines..

         Another topic - Jim Mederer said that "only power matters" when
         tuning
         the engine. That says that the load meter built into the
planetary
         reduction might really be a key component. Very cool. If you
         have a CS
         prop, you just lean the mixture until the torque peaks -
         assuming you
         have adequate cooling.

         Matt-


         I think the cylinder heat temperature thermal couple will also
         be a key component. I am very excited about Mark S's installation
         of CHT probes in his 3 rotor. This area is immediately adjacent
         to the spark plug.

         BTW Mark, I will drop off the 2, four channel data acq modules
when
         I see you a week from this coming Sunday.

         IMHO Jim's suggestion of running plugs two steps cooler than
normal
         is an excellent idea. If the engine will make it to the run up
         area with out fowling you have it made. It makes no sense at all
to
         run street car heat range spark plug in an aircraft engine.
Aircraft
         use is nothing like street car use.

         Paul Lamar


         Paul, Mark

         I'm curious about Mark's installation of thermocouples as shown
     in the
         photos. Will there be trouble with electromagnetic interference
from
         the the plug/plug wires? I know the wiring will be shielded, but
am
         curious as to what type/class of shielding will he use? Also
     what type
         of T/C and range and or part number. Thanks.

         Allen
         Houston

         That is something I hadn't heard of. The CHT probes are real
close
         to the plug wires in my O-470 and that does not appear to be
         a problem. On the other hand they and the spark plug wires are
         shielded. I guess it is possible. If we sample the data often
         enough the spark will appear in the data at idle.

         Have you experienced RF interference with thermocouples?

         I'll let Mark answer the last questions as I don't know
         what he used.

         Paul Lamar ...No rotor no motor.

         Hi Allen,

         I used regular unshielded thermocouple wire and quality
automotive
         silicone plug wires. I'm using Tracy's EC-2 and EM-2. So far,
     the CHT
         readings are rock steady, so I would conclude that interference
     isn't a
         problem. That could change with the data loggers, but I'll have
     to wait
         and see.

         Mark S.


     Mark,

     Would you mind telling me what kind of T/C's you are using?  I'm an
     instrument engineer that works in the oil/gas industry and it's
standard
     that T/C's have shielded wire so they won't pick up any stray
voltage.
     Are your thermocouples milivoltage types, say like a Type J, or some
     other range?  Are they grounded tips?  I'm just curious as I know the
     plug/plug wires do put out some high voltage (although I'm am only a
     neophyte when it comes to engines and aircraft).

     Allen
     Houston

Allen,
It is either type J or type K, don't recall.  It takes one type for the
cht and the other for the egt.  I bought the wire, stripped and wrapped
the ends, then melted the ends with a tig welder.  The TC wire
is 2-wire, covered in some medium brown cloth looking insulation.  I
didn't see any shielding.  The exhaust TC's were purchased from ACS.
They are the type with the nut that screws onto a welded bung.  Those
have shielding on them, but only for about 12" to whree the ring
terminals are located.  I just assumed the shielding was there to
protect the wire from the hot exhaust pipes.

Mark S.

[Joe Hull]
I'm a little behind on email...
But, the question was asked, "how many hours on the spark plugs?"  These
plugs had about 20 to 25 hours on them. Also, it was a BR9EQ - only one step
away from the coldest plug - if I understand Jim Mederer's chart correctly.

Thanx,
Joe Hull
Redmond, Wa  - Cozy Mark-IV, 71Hrs




The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.