Subject: Experimental air craft and rotary engines.
From: Rotary Engine
Date: 4/9/2007, 12:46 AM
To: AARotary Engine




    >          This looks good Paul..
    >
    >          More questions.. For Joe: Prior to the insulator
   failure, how
    >          recently
    >          had the plugs been out and inspected? From the dark
   color in the
    > pic
    >          posted, it doesn't appear that plug was running
   excessively hot.
    >          Hmm..
    >
    >          I think it was discussed before, but I can't remember the
    >          answer. Was
    >          it predictable that the plug being used might be
   susceptible to
    >          overheating and failure (based on published heat range)?
    >
    >          Maybe it should be standard practice to remove and
   inspect the
    > plugs
    >          after each flight for the first 10 hours?
    >
    >          I can see that picking a heat range for the plugs can be a
    >          challenge -
    >          especially given the number of variables involved. For
   instance,
    >          if the
    >          mixture is overly rich during ground running, it might be
    >          interpreted
    >          that the heat range is acceptably cool, when in fact at high
    >          power the
    >          plug may be running too hot.
    >
    >          When there is some standardization in ignition, fuel
   delivery,
    > and
    >          exhaust components, things are going to get easier... I
   wonder
    > what
    >          Powersport uses in their engines..
    >
    >          Another topic - Jim Mederer said that "only power
   matters" when
    >          tuning
    >          the engine. That says that the load meter built into the
    > planetary
    >          reduction might really be a key component. Very cool. If you
    >          have a CS
    >          prop, you just lean the mixture until the torque peaks -
    >          assuming you
    >          have adequate cooling.
    >
    >          Matt-
    >
    >
    >          I think the cylinder heat temperature thermal couple
   will also
    >          be a key component. I am very excited about Mark S's
   installation
    >          of CHT probes in his 3 rotor. This area is immediately
   adjacent
    >          to the spark plug.
    >
    >          BTW Mark, I will drop off the 2, four channel data acq
   modules
    > when
    >          I see you a week from this coming Sunday.
    >
    >          IMHO Jim's suggestion of running plugs two steps cooler than
    > normal
    >          is an excellent idea. If the engine will make it to the
   run up
    >          area with out fowling you have it made. It makes no
   sense at all
    > to
    >          run street car heat range spark plug in an aircraft engine.
    > Aircraft
    >          use is nothing like street car use.
    >
    >          Paul Lamar
    >
    >
    >          Paul, Mark
    >
    >          I'm curious about Mark's installation of thermocouples
   as shown
    >      in the
    >          photos. Will there be trouble with electromagnetic
   interference
    > from
    >          the the plug/plug wires? I know the wiring will be
   shielded, but
    > am
    >          curious as to what type/class of shielding will he use? Also
    >      what type
    >          of T/C and range and or part number. Thanks.
    >
    >          Allen
    >          Houston
    >
    >          That is something I hadn't heard of. The CHT probes are real
    > close
    >          to the plug wires in my O-470 and that does not appear
   to be
    >          a problem. On the other hand they and the spark plug
   wires are
    >          shielded. I guess it is possible. If we sample the data
   often
    >          enough the spark will appear in the data at idle.
    >
    >          Have you experienced RF interference with thermocouples?
    >
    >          I'll let Mark answer the last questions as I don't know
    >          what he used.
    >
    >          Paul Lamar ...No rotor no motor.
    >
    >          Hi Allen,
    >
    >          I used regular unshielded thermocouple wire and quality
    > automotive
    >          silicone plug wires. I'm using Tracy's EC-2 and EM-2. So
   far,
    >      the CHT
    >          readings are rock steady, so I would conclude that
   interference
    >      isn't a
    >          problem. That could change with the data loggers, but
   I'll have
    >      to wait
    >          and see.
    >
    >          Mark S.
    >
    >
    >      Mark,
    >
    >      Would you mind telling me what kind of T/C's you are
   using?  I'm an
    >      instrument engineer that works in the oil/gas industry and it's
    > standard
    >      that T/C's have shielded wire so they won't pick up any stray
    > voltage.
    >      Are your thermocouples milivoltage types, say like a Type J,
   or some
    >      other range?  Are they grounded tips?  I'm just curious as I
   know the
    >      plug/plug wires do put out some high voltage (although I'm
   am only a
    >      neophyte when it comes to engines and aircraft).
    >
    >      Allen
    >      Houston
    >
    > Allen,
    > It is either type J or type K, don't recall.  It takes one type
   for the
    > cht and the other for the egt.  I bought the wire, stripped and
   wrapped
    > the ends, then melted the ends with a tig welder.  The TC wire
    > is 2-wire, covered in some medium brown cloth looking insulation.  I
    > didn't see any shielding.  The exhaust TC's were purchased from ACS.
    > They are the type with the nut that screws onto a welded
   bung.  Those
    > have shielding on them, but only for about 12" to whree the ring
    > terminals are located.  I just assumed the shielding was there to
    > protect the wire from the hot exhaust pipes.
    >
    > Mark S.

   [Joe Hull]
   I'm a little behind on email...
   But, the question was asked, "how many hours on the spark plugs?"  These
   plugs had about 20 to 25 hours on them. Also, it was a BR9EQ - only
   one step
   away from the coldest plug - if I understand Jim Mederer's chart
   correctly.

   Thanx,
   Joe Hull
   Redmond, Wa  - Cozy Mark-IV, 71Hrs



Thanks Joe.. That's interesting.

I wonder if there was something else wrong with the plug to start with.


Matt-



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.