Subject: Which parts go with which?
From: Rotary Engine
Date: 4/9/2007, 12:17 PM
To: AARotary Engine



     > I bought 3 13B engines sight unseen. They were described as
    rebuildable,
     > two 91s and a 86. It turns out they were a box full of parts. I
    thought
     > they were assembled engines, but then I didn't ask. Dumb me.
     >
     > Some of the parts are marked as #1, #2 and #3, all 3 e-shafts and
    some
     > of the rotors and some of the other parts. None of the counter
    weights
     > are marked. I can't see any complete set of parts that are marked the
     > same to assemble a complete engine.
     >
     > In general the parts do indeed look re-usable. The ones that we have
     > measured pass Mazda's tests.
     >
     > The problem is that I don't know which goes with which. I am
    especially
     > concerned about the counter weights. None of the counter weights are
     > marked.
     >
     > Is it permissible to just assemble an engine with whatever parts
    seem to
     > belong to each other?
     >
     > What to do?
     >
     > Doc Custer
     > Retired Software Engineer and sometime Audiologist

    ---------------------------------------------------
     > As well you should be Doc :)
     > I don't know how to identify counter weights and I doubt any
     > of the shop manuals tell you how either. I could be wrong
     > but your best bet is call Mazdatrix and ask for John.
     > Other than that people mix and match all the time as long
     > as the rotors are the same. I would for sure have it professionally
     > dynamically balanced.
     >
     > Take some detailed pictures of the counter weights and
     > upload them. Some one on here might recognize them.
     >
     >
     > Paul Lamar ...No rotor no motor.


    Hi Doc;
    You can assemble anything and it will run, for a while...:) The short
    answer is no.

    Front and rear counterweights(CW) (or flywheel which have the CW cast
    into them)
    must match the rotor series.  e.g. series4 OR series5/6 are the same.
    Many CWs look very similar - the easiest way is to weigh them.
    Digital scales with gram accuracy are cheap.

    Mazdatrix has a FAQ: (plus lots of other good info they have been kind
    enough to share)
        http://www.mazdatrix.com/faq/Rcounterweights.htm
    Here is another thread:

    http://www.rx7club.com/showthread.php?t=467955&highlight=rear+counterweight+specs
    <http://www.rx7club.com/showthread.php?t=467955&highlight=rear+counterweight+specs>

    Generally:
    S4 rear CW = 1855g, typically +-5g, 1 or 2 balance holes
    S4 front CW = can't find the info right now.

    S5 rear CW = 1820g +10g?, typically 2 or 3 balance holes
    S5 front CW ~= 1200g with washer

    S6 are the same as S5, ones I have measured are usually lighter by a
    gram or so.

    Here are some photos comparing CWs, I'm can't remember where I found
    these?

    Also attached is a pic from nopistons.com <http://nopistons.com> on
    balancing:

    Cheers
    Cary




Paul, here is a picture that highlights the difference between the
series 4 and series 5 front counter weight.  The series 5 is on the left.

The S4 vs S5 rotor you can tell apart because the S5 have machine groves
in the rotor face cavity.

-- 

David Leonard

Turbo Rotary RV-6 N4VY
N4VY.RotaryRoster.net <http://N4VY.RotaryRoster.net>
www.RotaryRoster.net <http://www.RotaryRoster.net>
leonardiniraq.blogspot.com <http://leonardiniraq.blogspot.com>


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.