Subject: Which parts go with which?
From: Rotary Engine
Date: 4/13/2007, 9:49 PM
To: AARotary Engine




    >  I think Buly bought a NA 13B Cosmo engine
    > from Japan.
    >
    > Paul Lamar ...No rotor no motor.

   I bought my Cosmo 13B from a local engine importer, and it was a Twin
   Sequential Turbo. Now it is running as a NA, since the
   Lamar Stock Turbo Experiment failed :)
   Buly

   Yes it is my stock turbo but not failed yet. The first time I saw
   it on the Mecanair (now Mistral) rotary aircraft engine at OSH I said:
   "Wow look at that. A stock 1989-1991 Mazda 13B turbo rotary aircraft
   engine." Water cooled, waste gate, heat shielded and all plumbed up
   with a very compact installation. Perfect for aircraft use.

   Unfortunately I under
   estimated the HP of the turbine and over estimated the effectiveness
   of the waste gate. John Slade installed one and proceeded to blow it
   up due to a combination of over temp. and over rev. Mecanair

   became Mistral and Mistral tasked Emory Riddle to install and test
   the turbo
   engine in a Piper Arrow and proceeded to blow the turbo up.
   Unfortunately they did not tell us about that until way
   later. Dave Leonard installed the Mazda turbo engine in his RV6 and
   proceeded to blow up the turbo.

   By that time I had figgered out the turbine would make an excellent
   turbo compound turbine because of the huge amount of excess HP
   it possessed. The reason it has so much HP is it is needed to
   rapidly accelerate the turbo charger for use in cars that need
   the boost RIGHT NOW. Not in a second or two.

   You were not on the
   Newsletter Buly at that time so you proceeded to install the
   stock turbo and blow it up also. My main man Dave Leonard persevered,
   figured out the problem and fixed it by using a larger compressor
   to load and slow down the turbine. He also bored out the hole in
   the waste gate and removed the waste gate flapper. Apparently it
   is now fixed. We will soon know as Dave is getting ready to fly
   again after his fine service tour in Iraq. Thank you again Dave
   for all you do here and in Iraq.

   BTW Buly I can always tell when I go somewhere and shutdown the
   Newsletter, who reads ALL the messages before posting
   and who doesn't :) I am in Tombstone AZ and was lucky enough
   to find a reasonably priced  motel that had wireless.

   Paul Lamar ...No rotor no motor.

   Well, isn't that a fine "how-ya-do"?  I have the Mistral intake and was
   fudging about for hours on how to get the turbo manifold and turbo
   to fit
   since the Mistral Intake has in injector rail directly interfering with
   where the turbo assembly should be.  I remember reading that the
   injectors
   were placed there since that was determined to be the best
   location...........BUT, NOOOOOOW, as I see their turbo install, the
   injector
   rail is missing as the turbo is slotted in that location.
   GEEEEEESH.  So
   it goes.

   Back to wire runs.

   All the best,

   Chris

   I am sure we can make it work Chris. Send me some pictures of
   what you have so far as I recall there are more than one Mistral
   manifolds.

   What does Francois have to say about it.

   --
   Paul Lamar ...No rotor no motor.


Hey Chris,
Does Mistral sell their intake to the public?
That would be a great option!  It looks like it would be just about perfect.
Don



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.