Subject: Selecting a turbo charger for aircraft use.
From: Rotary Engine
Date: 4/14/2007, 4:53 PM
To: AARotary Engine



   I bought my Cosmo 13B from a local engine importer, and it was a Twin
   Sequential Turbo. Now it is running as a NA, since the
   Lamar Stock Turbo Experiment failed :)
   Buly

   Yes it is my stock turbo but not failed yet. The first time I saw
   it on the Mecanair (now Mistral) rotary aircraft engine at OSH I said:
   "Wow look at that. A stock 1989-1991 Mazda 13B turbo rotary aircraft
   engine." Water cooled, waste gate, heat shielded and all plumbed up
   with a very compact installation. Perfect for aircraft use.

   Unfortunately I under
   estimated the HP of the turbine and over estimated the effectiveness
   of the waste gate. John Slade installed one and proceeded to blow it
   up due to a combination of over temp. and over rev. Mecanair
   became Mistral and Mistral tasked Emory Riddle to install and test
   the turbo
   engine in a Piper Arrow and proceeded to blow the turbo up.
   Unfortunately they did not tell us about that until way
   later. Dave Leonard installed the Mazda turbo engine in his RV6 and
   proceeded to blow up the turbo.

   By that time I had figgered out the turbine would make an excellent
   turbo compound turbine because of the huge amount of excess HP
   it possessed. The reason it has so much HP is it is needed to
   rapidly accelerate the turbo charger for use in cars that need
   the boost RIGHT NOW. Not in a second or two.

   You were not on the
   Newsletter Buly at that time so you proceeded to install the
   stock turbo and blow it up also. My main man Dave Leonard persevered,
   figured out the problem and fixed it by using a larger compressor
   to load and slow down the turbine. He also bored out the hole in
   the waste gate and removed the waste gate flapper. Apparently it
   is now fixed. We will soon know as Dave is getting ready to fly
   again after his fine service tour in Iraq. Thank you again Dave
   for all you do here and in Iraq.
   ------------------------------------------------------

   It is not too difficult to match the compressor to the
   amount of engine HP you would like to generate. That is the easy
   part. We have several spread sheets from different people
   that achieve that task. I suspect the problem is the turbines
   that go with these compressors are way too powerful for aircraft
   use. If somebody went to Garrett and said I won't x compressor map
   Garrett would give them a turbo charger turbine designed for
   automotive use. In other words a turbo charger that would accelerate
   rapidly and then be backed off to shift. If run at sustained high
   power it would soon over rev and explode I have no doubt.

   We need HP data on Garret turbines that will
   not over rev the turbochargers at steady state high altitude
   use. So far and as far as I can tell that info is not fourth
   coming from Garrett. I suspect we need an A/R over one.
   I also suspect no off the shelf automotive turbo charger
   is going to work. We will have to mix and match turbine with
   compressor. Garrett does not discuss this scenario on their
   web site. Also they donnot discuss turbocharger acceleration.
   If we knew the rotating moment of inertia for the
   compressor/shaft/turbine and the acceleration in terms of RPM per second
   per second we could figure out the turbine HP.

   http://www.turbobygarrett.com/turbobygarrett/tech_center/turbo_tech103.html

   Paul Lamar ...No rotor no motor.

   Paul,

   I have been working on adding the turbine side to my spreadsheet for
   the last few days.

   Modeling a turbine is very easy -- with one big proviso -- that you
   know the pressure of the gases on the inlet side. In other words, we
   need to know exhaust pressures coming out of the engine.

   Ahh, but there's the rub. Estimating the engine exhaust pressures is
   the hard part, because you basically have to come up with a
   mathematical model of the Otto cycle engine that will give you
   cylinder pressures and exhaust pressures. I thought this was going to
   be as easy as modeling a turbine, but it's not. All the models for
   Otto cycle engines are very complex if they are to be of any use. I
   would appreciate hearing from anyone with ideas on this.


   Also, I have to disagree with your comments about big turbines being
   "too powerful" for a rotary aircraft engine. Big turbines only make
   lots of power if they have a lot of exhaust energy to work with.

   Big turbines are used on relatively small certified aircraft engines
   for a very good reason -- the big turbine won't spin up until there
   is significant exhaust energy going across the turbine wheel. And
   that only happens at altitude, where the pressure ratio between
   intake and outlet is high.

   That is why the aircraft turbonormalizing systems can work well with
   fixed wastegates. There is simply not enough energy in the exhaust
   at sea level for the big turbine to spin up and make much, if any,
   boost from the compressor. Therefore an adjustable wastegate is not
   needed. Here's why:

   When the plane climbs up into thinner air, the pressure difference
   between the intake side of the turbine and the outlet side
   increases. This is because the outlet side of the turbine is equal
   to ambient pressure, which is dropping. The inlet side of the
   turbine is simply the exhaust pressure of the engine. This is a
   function of the intake manifold pressure.

   So we see that if the intaek manifold pressure remains the same
   -- which it will be if you have boost --  and the outlet pressure
   drops, the net result will be a steeper pressure gradient across the
   turbine wheel. The higher you go, the lower the ambient pressure
   drops and the bigger the pressure ratio across the turbine will be
   (provided you can maintain a steady intake manifold pressure, or MAP).

   What does that mean? This pressure ratio between the inlet and
   outlet side of the turbine is what is called a turbine pressure
   ratio, TPR, and is the single biggest factor in how much power any
   turbine will make.

   The higher the TPR, the more quickly the gases will acceleerate
   across the wheel, because air, or any fluid,  will always accelerate
   more quickly from an area of high pressure to low pressure.

   You can see this with a tire that is pumped up to a high perssure
   and one that is nearly flat. The highly pressurized tire will blow a
   very energetic jet if you open the valve, while the nearly flat tire
   will have a very weak jet. Or suppose you have a tire that is pumped
   to a very high pressure, but you also pressurize the room in which
   it is sitting (like a barometric chamber). Now when you open the
   valve, there will be very little energy in the jet, just like the
   almost flat tire at ambient pressure. This illustrates that it is
   the pressure ratio, not absolute pressures that is the key.

   How does this translate into power? The rapid acceleration of gas
   across the turbine wheel when there is a a high TPR creates high
   momentum, and that momentum imparts force to the turbine wheel,
   which in turn, will spin faster and make more power. (Every turbine
   pilot is familiar with TPR and NPR, the nozzle pressure ratio, which
   is used to set engine power, along with rpm.)

   http://www.grc.nasa.gov/WWW/K-12/airplane/powtrbth.html

   Like I said it is an easy matter to calculate the turbine hp with
   very good accuracy if you know the inlet and outlet pressures --
   using the ideal gas law, which equates temperatures, pressures and
   volumes.

   But the whole thing depends on being able to estimate exhaust
   pressure coming out of the engine -- because this is the inlet side
   of the turbine. (Whether the turbine is driving a compressor, or is
   recovering power and feeding it mechanically back to the engine shaft).

   Another thing you touched on is that we don't have much turbine data
   from Garrett. This is true, but not such a big problem.

   For example if you take a compressor map on my spreadsheet and see
   how much power that compressor is absorbing in the heart of its map,
   you know the turbine that is matched with that compresoror (the one
   Garret inlcudes as a matched set), will be working at its design point.

   Now, if you know the exhaust flow and pressure coming out of the
   engine, you can figure out just how much power is actually available
   to drive a turbine. This will always be more than it takes to drive
   the compressor. So you know how much excess hp your exhaust is
   capable of making, beyond driving the compressor.

   What you do then is simply go to a bigger map and find a compressor
   that can absorb all of the exhaust power you just calculated. You
   then take the turbine that goes with that really big compressor and
   use it with the smaller compresor that you selected previously. This
   will work just fine with a turbocompound engine as well.

   True, having more turbine data would make things even better, but it
   is not really necessary. And since it is not forthcoming from
   Garrett, it is a moot point.


   Regards,

   Gordon.


I didn't use the words "big turbine" Gordon. What I did say was:

"turbines that go with these compressors are way too powerful for aircraft
use."

Almost any physical size turbine will generate a wide range of power
depending on the pressure or velocity of the gases feeding it and the RPM it
is capable of. HP is proportional to torque times RPM.

The back exhaust pressure on the engine will be a strong function
of the turbine used. Low A/R's numbers are not free. You won't know the back
pressure until you know more about the turbines available. Also the engine
HP is a function of the exhaust back pressure. It is  a chicken and egg
problem.  Good luck until you come up with some meaningful off the shelf
turbine information. So far Dave Leonard and others have gone through the
trial and error process of adding a larger compressor and opening up the
waste gate. Dave is closer to a solution than anybody IMHO.

What we need to do is measure the exhaust back pressure, the RPM
of the turbo charger, engine MAP and the temperature
drop across the turbine. That will give us some data points.
Dave is closer than any of us so Dave if you would please measure the EGT
on both sides of the turbine that would be a start. Then we need
a turbo charger tachometer. Once we have some of that kind of data
We can tell if we need to go up or down on the A/R.

Also the life of the turbine is a factor so you want the lowest turbo
charger RPM and smallest diameter turbine that does the job. The
centrifugal force on the blades is m times V^2/r Where m is the mass of the
blade and V is its tangential velocity of the blade and r is the radius of the
blade's CG. Of course V is also a function of r at any given RPM.

The strength of the blade is an inverse exponential function of the
temperature. Needless to say the rotary applies extra requirements on turbo
chargers due to the higher temperature of its exhaust.

Higher tensile strength to density ratio high temperature materials
like Inconel help.

The problem here is not finding a turbo charger that generates
the boost. Almost any turbo charger will do that. The problem
is finding one that lives, generates the required boost and imposes a
minimum of back pressure on the engine.

Even Hughe MacInnes says: "Start with your best guess  and adjust." :)

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.