Here is Doc and his three generation family.
He has done a very fine job on this production low aerodynamic loss
p-port slide throttle.
He is going to ship it to me and I will see if I can get Mazdatrix or
Racing Beat to distribute it.
--
Paul Lamar ...No rotor no motor.
Doc
Nice jog. Is Mazdatrix, or anyone going to actually test the slide
throttle performance and operation on a running engine before selling it?
Doug
We already did that Doug. Perhaps you were in Nepal at the time.
240 HP at 6500 RPM. Mark Suspinski is getting ready to fly it soon.
Of course slide throttles have been used on Mazda engines before.
In fact they were used on the Lemans winning Mazda four rotor p-port engine.
They date back on car engines close to 100 years.
Paul Lamar
Paul,
Yes I saw the data. Actually I understood it you didn't use the slide
throttle and had to quickly rig up Webber Carbs for the test. That version
of the slide throttle had a very thin Teflon sheet as I recall. Perhaps you
tested again this year when I was in Nepal? .
Doug Fir
The engine ran fine on the dyno with the slide throttle. I was unable to get
the mixture
to stabilize because the dyno load is different than prop load and we were
using
Tracy's EFI system with the slide throttle. Tracy's EFI system is designed for
a fixed
pitch prop load which is a strict function of RPM. In other words for each RPM
there
is a given single load. Dyno load is like car load in that the load can vary
all over
the lot at any given RPM. That takes more sophisticated sensors than Tracy
provides.
Namely it takes a mass air flow sensor and probably a throttle position
sensor. Tracy
system is working on manifold air pressure, RPM and intake air temperature
alone. A
carburetor works on an airflow sensor (a venturi) so it does a much better job
of
adjusting the mixture at any given RPM for a wide range of loads.
That is not to say Tracy's system will not work on a dyno. At $650 a day I ran
out of time and money to get it tuned properly. I suspect Tracy's system is
going
to have a hard time dealing with a variable pitch prop load automatically. You
will
need to fine tune the mixture manually as you change the pitch and load at any
given
RPM.
In your case you are using a fixed pitch prop based dyno so you will find
Tracy's system
will work fine and be much quicker to tune.
These Teflon slide throttles are not rocket science. There is absolutely no
reason they won't work with a fixed pitch prop load and Tracy's system.
No different than a butter fly throttle. The thickness of the Teflon slide
has nothing to do with it.
Mark Supinski also ran the p-port slide throttle engine with prop load and
Tracy's
EFI system with the same slide thickness Doc is now building. It may have been
while you
were in Nepal. It ran fine as far as I know but it was leaking coolant into
the
combustion chamber so we had to start over, disassemble the engine, replace
and re-seal
the p-port tubes at great expense for both Mark and I. Thank you again Mark
for your
perseverance, time and money. I used the wrong epoxy and improper aluminum
preparation
on the first go around. It is called R&D. Long story.
BTW Mark Steitle agreed to try tig welding a p-port SS tube to the steel liner
on his
junk p-port rotor housing while I was in Austin a week ago Sunday.
Mark Steitle is a very talented tig welder among his many other excellent
fabrication
skills.
Paul Lamar ...No rotor no motor.
Paul,
Ok that is good news on the slide throttle. Bad news on Tracy's controller I
bought. I was just thinking the other day on how I was going to control the
injector timing near the P-ports. BTW in retrospect you where correct in it
not being a good idea to inject fuel at the oil injection location. With the
intake port already closed and ethanol's cooling effect, the pressure will
drop significantly. I was only thinking about it for idling rpms but I may
have to drop the idea and stick with two larger injectors per port.
On the fan dyno I was actually planning to have the props fans angles able
to be changed during operation through an electric controlled mechanism.
Since I will fly with a C/S prop it is paramount I test by controlling rpm
with the load. Darn on the controller. What are my options now?
MegaSquirt? X 2?
Doug Fir
Megasquirt is a good solution. Cheap too. Use two for a backup.
I would not use one injector per rotor. You need a backup.
If you are not going to use Tracy's system.
I would use the constant dribble system PWM fuel pump scheme
controlled by an easy to program PICAXE system. Super simple
super low cost and super reliable. It has a built in
engine monitoring system with a miniature PC on the instrument
panel. So cheap you can use one for each fuel pump.
You can add a pot controlled by the throttle cable.
--------------------------OLD MESSAGE-------------------------------
This message triggered an idea Doc. A combination of
EFI and the low pressure dribble system. Since one needs
a low pressure electric fuel pump no matter what... control the pump
pressure PWM with a 44 cent PIC microcomputer that takes data in
from a MAP sensor, RPM and a leaning knob pot on the instrument
panel.
snip..
Voila!!! Super simple low pressure EFI!!!! The PIC has an A to D
for the MAP sensor and leaning knob and an interrupt
for the RPM. Should take all of an hour to write the BASIC
program :) No injectors. Small holes in the p-port slide throttle
instead. No injector wires in the cowl to burn. Only wires go
to the low cost, low pressure, off the shelf fuel pump.
No leaning needle valve. No metering ramp in the slide throttle
or multiple holes. Just one small hole There is
a small hose to the MAP sensor mounted on the PIC PC board which
is just behind the panel with the PC board mounted leaning pot
shaft sticking through the panel.
If you want to spend a bit more than 44 cents on the PIC you can
add a USB data acquisition interface and download the flash stored
historical data to a PC. Since THE pic knows the fuel flow it knows
the GPH. Since the PIC knows the GPH and it could take NEMA 0183
ASCII data in from a GPS and calculate and display the MPG IN
REAL TIME!!!!
------------------------------------------------------------------
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.