>
> >>>> Here is Doc and his three generation family.
> >>>> He has done a very fine job on this production low
> aerodynamic loss
> >>>> p-port slide throttle.
> >>>>
> >>>> He is going to ship it to me and I will see if I can get
> Mazdatrix or
> >>>> Racing Beat to distribute it.
> >>>> --
> >>>> Paul Lamar ...No rotor no motor.
> >>>>
> >>>
> >>> Doc
> >>>
> >>> Nice jog. Is Mazdatrix, or anyone going to actually test
> the slide
> >>> throttle performance and operation on a running engine
> before selling it?
> >>>
> >>> Doug
> >>>
> >>> We already did that Doug. Perhaps you were in Nepal at the time.
> >>> 240 HP at 6500 RPM. Mark Suspinski is getting ready to fly
> it soon.
> >>> Of course slide throttles have been used on Mazda engines before.
> >>> In fact they were used on the Lemans winning Mazda four
> rotor p-port engine.
> >>> They date back on car engines close to 100 years.
> >>>
> >>> Paul Lamar
> >>
> >> Paul,
> >>
> >> Yes I saw the data. Actually I understood it you didn't use
> the slide
> >> throttle and had to quickly rig up Webber Carbs for the test.
> That version
> >> of the slide throttle had a very thin Teflon sheet as I
> recall. Perhaps you
> >> tested again this year when I was in Nepal? .
> >>
> >>
> >> Doug Fir
> >>
> >> The engine ran fine on the dyno with the slide throttle. I
> was unable to get
> >> the mixture
> >> to stabilize because the dyno load is different than prop
> load and we were
> >> using
> >> Tracy's EFI system with the slide throttle. Tracy's EFI
> system is designed
> >> for
> >> a fixed
> >> pitch prop load which is a strict function of RPM. In other
> words for each
> >> RPM
> >> there
> >> is a given single load. Dyno load is like car load in that
> the load can vary
> >> all over
> >> the lot at any given RPM. That takes more sophisticated
> sensors than Tracy
> >> provides.
> >> Namely it takes a mass air flow sensor and probably a
> throttle position
> >> sensor. Tracy
> >> system is working on manifold air pressure, RPM and intake
> air temperature
> >> alone. A
> >> carburetor works on an airflow sensor (a venturi) so it does
> a much better
> >> job
> >> of
> >> adjusting the mixture at any given RPM for a wide range of loads.
> >>
> >> That is not to say Tracy's system will not work on a dyno. At
> $650 a day I
> >> ran
> >> out of time and money to get it tuned properly. I suspect
> Tracy's system is
> >> going
> >> to have a hard time dealing with a variable pitch prop load
> automatically.>> You
> >> will
> >> need to fine tune the mixture manually as you change the
> pitch and load at
> >> any
> >> given
> >> RPM.
> >>
> >> In your case you are using a fixed pitch prop based dyno so
> you will find
> >> Tracy's system
> >> will work fine and be much quicker to tune.
> >>
> >> These Teflon slide throttles are not rocket science. There is
> absolutely no
> >> reason they won't work with a fixed pitch prop load and
> Tracy's system.
> >> No different than a butter fly throttle. The thickness of the
> Teflon slide
> >> has nothing to do with it.
> >>
> >> Mark Supinski also ran the p-port slide throttle engine with
> prop load and
> >> Tracy's
> >> EFI system with the same slide thickness Doc is now building.
> It may have
> >> been
> >> while you
> >> were in Nepal. It ran fine as far as I know but it was
> leaking coolant into
> >> the
> >> combustion chamber so we had to start over, disassemble the
> engine, replace
> >> and re-seal
> >> the p-port tubes at great expense for both Mark and I. Thank
> you again Mark
> >> for your
> >> perseverance, time and money. I used the wrong epoxy and
> improper aluminum
> >> preparation
> >> on the first go around. It is called R&D. Long story.
> >>
> >> BTW Mark Steitle agreed to try tig welding a p-port SS tube
> to the steel
> >> liner
> >> on his
> >> junk p-port rotor housing while I was in Austin a week ago Sunday.
> >> Mark Steitle is a very talented tig welder among his many
> other excellent
> >> fabrication
> >> skills.
> >>
> >> Paul Lamar ...No rotor no motor.
> >
> > Paul,
> >
> > Ok that is good news on the slide throttle. Bad news on
> Tracy's controller I
> > bought. I was just thinking the other day on how I was going
> to control the
> > injector timing near the P-ports. BTW in retrospect you where
> correct in it
> > not being a good idea to inject fuel at the oil injection
> location. With the
> > intake port already closed and ethanol's cooling effect, the
> pressure will
> > drop significantly. I was only thinking about it for idling
> rpms but I may
> > have to drop the idea and stick with two larger injectors per port.
> >
> > On the fan dyno I was actually planning to have the props fans
> angles able
> > to be changed during operation through an electric controlled
> mechanism.> Since I will fly with a C/S prop it is paramount I
> test by controlling rpm
> > with the load. Darn on the controller. What are my options now?
> > MegaSquirt? X 2?
> >
> > Doug Fir
> >
> > Megasquirt is a good solution. Cheap too. Use two for a backup.
> > I would not use one injector per rotor. You need a backup.
> >
> > If you are not going to use Tracy's system.
> > I would use the constant dribble system PWM fuel pump scheme
> > controlled by an easy to program PICAXE system. Super simple
> > super low cost and super reliable. It has a built in
> > engine monitoring system with a miniature PC on the instrument
> > panel. So cheap you can use one for each fuel pump.
> > You can add a pot controlled by the throttle cable.
> >
> >
> >
> > --------------------------OLD MESSAGE--------------------------
> -----
> > This message triggered an idea Doc. A combination of
> > EFI and the low pressure dribble system. Since one needs
> > a low pressure electric fuel pump no matter what... control
> the pump
> > pressure PWM with a 44 cent PIC microcomputer that takes data in
> > from a MAP sensor, RPM and a leaning knob pot on the instrument
> > panel.
> >
> > snip..
> >
> > Voila!!! Super simple low pressure EFI!!!! The PIC has an A to D
> > for the MAP sensor and leaning knob and an interrupt
> > for the RPM. Should take all of an hour to write the BASIC
> > program :) No injectors. Small holes in the p-port slide throttle
> > instead. No injector wires in the cowl to burn. Only wires go
> > to the low cost, low pressure, off the shelf fuel pump.
> > No leaning needle valve. No metering ramp in the slide throttle
> > or multiple holes. Just one small hole There is
> > a small hose to the MAP sensor mounted on the PIC PC board which
> > is just behind the panel with the PC board mounted leaning pot
> > shaft sticking through the panel.
> >
> > If you want to spend a bit more than 44 cents on the PIC you can
> > add a USB data acquisition interface and download the flash stored
> > historical data to a PC. Since THE pic knows the fuel flow it knows
> > the GPH. Since the PIC knows the GPH and it could take NEMA 0183
> > ASCII data in from a GPS and calculate and display the MPG IN
> > REAL TIME!!!!
> > ---------------------------------------------------------------
> ---
> >
> > --
> > Paul Lamar ...No rotor no motor.
>
>
> Paul,
>
>
> Yes two injectors per port or four total. I thought you told me
> I couldn't
> use this the simple PIC controlled system with a engine under
> boost. I
> believe you mentioned the need to possibly control a waste gate.
> In any
> case I have enough on my plate now so it would be wise to stick
> with the
> EFI system and go through the MEGA SQUIRT info again. I'll be
> selling the
> EC-2 unit if anyone is interested. It is still new and in the
> box and
> received one year ago.
>
> DougFir
>
> Yes I forgot. You are using a turbo charger or turbo compound.
> That leaves Megasquirt. A little harder to program but I can help
> if you wish. I happen to know 68XX ASM language. You can also
> get a
> lot of help on the Internet due to the huge Megasquirt community.
> I think they have some left over A to D's to add a leaning pot
> and TIT sensors.
>
> There is another possibility and that is use a separate PICAXE
> to control
> the turbo waste gate. Probably much easier to do as you are
> trading real cheap
> easy to program hardware for a difficult to program Megasquirt.
> Also you wind
> up with a bit more redundancy.
>
> Paul Lamar ...No rotor no motor.
I just bought an EC2 and wanted to go with a constant prop and PPort. I
could live without a constant speed prop. Could I still use EC2 and PPort
without major mod ???
Marc
Nexus Mustang
It really remains to be seen just how inconvenient this turns out to be.
You will have to adjust the mixture for each pitch setting and
RPM combination. I think Tracy will be forced to deal with it sooner
or later. Buly should soon know as he is running a variable pitch
prop sort of.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.