Hi Paul
I sent you some new pictures and a couple of question about my ross drive a
week ago and have not seen it posted. I new to this stuff. Are you work on
an answer or did you not get it?
Thanks Mark Kirkpatrick
Sorry I was on the road and I missed it.
Paul Lamar
-----------------------------------------------------------------------
Hi Paul
Got some time to finish taking my redrive apart. I tell you, when Ross made
this thing I don't think he had any intention of ever having to work on it.
I'm thinking about trying to rebuild it so you could actually replace parts
without having to re-machine everything. I took some new pictures of the
drive and am still interested in input from anyone on what might have caused
the failure. Paul I spent some time looking at Tracy's drive. It looks to
me like the sun gear is supported in the front, but I can't tell for sure.
The roller bearing that supported the front of the sun gear on my Ross drive
was completely destroyed. I not sure which went first the chicken or the
egg.
I put some questions on the pic's I sent, but if you were going to modify a
Ross drive what would be at the top of your list?
Also does anyone have a good source for buying bearings.
On a different note I have been using Tracy's EC2 with an in flight
Adjustable Ivo Prop. You spend a lot of time with the manual mixture
control. I've found the most noticeable and most inconvenient time is during
decent and landing. I 've tried to setup the map to work best at that time
and use the manual mixture for climb and cruise.
Mark Kirkpatrick
The top of the list is to find out if the Ross is machined concentric.
First the thing to do is bolt the housings together and bolt them to the engine.
I would make a mandrill that just fit in the front housing bore with a pilot
that just fit in the clutch shaft pilot hole in the back end of the e-shaft.
This is critical to the overall correct alignment of the box. There may be another
way of doing it. Perhaps with a laser.
If that is correct you should replace all the bearings with new ones.
I would not attempt to replace the needle thrust bearings with ball bearings.
Replace the prop shaft temporarily and use a dial indicator to make sure the ring
gear is running true. The next problem is making sure the
planet carrier is located concentric and square in the housing. A little float will
not hurt as it will self center on the ring gear. You need only two supports
for the sun gear. The gear itself and the pilot hole in the e-shaft.
the sun gear will self center on the planet carrier and in so doing equalize
the tooth loads on all six planet gears. Now you must provide a thrust
bearing for the sun gear. I'll go over that latter. Basically it will require
three needle bearings back to back.
Slauson Transmisson sells the Ford parts.
http://www.slauson.com/
There are bearing supply houses in all major cities and towns.
"On a different note I have been using Tracy's EC2 with an in flight
Adjustable Ivo Prop. You spend a lot of time with the manual mixture
control. I've found the most noticeable and most inconvenient time is during
decent and landing. I 've tried to setup the map to work best at that time
and use the manual mixture for climb and cruise."
I am not surprised. As far as I can tell Tracy's system cannot automatically
handle changing prop loads and that is what happens when you change the pitch.
We had the same problem on the dyno. For a fixed pitch prop it is a 2D system.
For each RPM there is a given prop load. On a variable pitch prop the load
at any RPM can vary all over the ball park and that is a 3D system.
BTW That answers the question I had for Buly.
Tracy uses only MAP, RPM and intake
temperature to set the mixture. I think a mass airflow sensor and maybe a throttle
position sensor will be required to automatically handle changing prop loads.
Read up on the Megasquirt web sites for more information. Mistral probably knows
a lot more about this as their system is set up for a constant speed prop from
the get go. Francois, what type sensors are you using?
Aircraft carbs over timed EFI are looking better and better to me all the time.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.