Subject: OEM engine computer (Stock Engines in Homebuilt Planes
From: Rotary Engine
Date: 5/3/2007, 11:35 AM
To: AARotary Engine




   Paul, and the group

   A lot has been written about aftermarket computers for our aero
   conversions. However, is there any reason why the stock engine computer
   can not be used? Does anyone have any experience in using stock? Good or
   bad? How does one go about configuring the stock unit for aircraft use?
   Engine is a 13b single turbo with fuel injection.

   Thanks and regards,

   --
   Erik Snyman
   Messina
   South Africa.

   Perry Mick has over 500 hours with the stock computer. There are a
   few tricks
   however. The stock computer takes in some data from certain places that
   don't exist in an airplane. I'll let Perry explain it if he doesn't
   mind.
   As I recall the big hang up is leaning it. Perry was working on a
   solution
   for that as I recall.

   ---------------------------------------------------------------------
   BTW HKS makes a bunch of add on device that change the output of the
   varies
   RX8 engine sensors in real time. I suspect they are basically
   PICAXEs with
   analog to digital converters that take in the sensor voltage and
   covert it to a
   different analog output voltage to be fed into the stock OEM computer.
   I think this is the way they did it with this 390 HP turbo RX8 engine.
   http://www.rotaryeng.net/Turbo-RX8a.jpg

   For example if you wanted to lean the OEM computer for use at
   high altitude you would take in the mass air flow sensor output voltage
   and change it so the the stock OEM computer thought it was getting less
   air than it actually was. Consequently it would put out less fuel.
   Pretty easy to do with a $30 PICAXE.

   Paul Lamar ...No rotor no motor.


   Paul,

   I would have reservations about using an OEM computer at high
   altitudes. (Or any computer that has not been proven for aircraft
   use, for that matter.)

   The reason is that as atmospheric pressure drops, it becomes easier
   for electrical current to jump gaps and end up where it's not
   supposed to. We see this in aircraft magnetos that have arc-over at
   higher altitudes. That's why some of the turbocharged planes have
   pressurized magnetos.

   It is anyone's guess how the electronics inside an engine computer
   will behave at pressure of even half that at sea level (15,000 feet
   approx.). They may work fine, they may not.

   My own opinion is that I would rather not fly a stock engine
   computer above 10 to 12 thousand feet. At this altitude the stock
   computer should be able to handle the leaning anyway.

   For any serious flying above that, my preference is for a purely
   mechanical ignition system (flywheel magneto, a la Rotax), and carb
   or mechanical fuel injection.


   Regards,

   Gordon.

   Those are real high voltages Gordon. Not a problem at 5 volts.
   Sparks are
   20,000 volts and up.
   Most engine computers have a coating over the parts called a conformal
   coating which acts as an insulator. At Pikes peak in Colorado there
   is a road to the top at 14,000 feet as I recall where the
   public can and do drive to the top. Perry has had no trouble with
   this in
   over 500 hours.

   Paul Lamar ...No rotor no motor.

   Paul,

   Yes, the voltage in magnetos is very high, but so is the distance
   that the current jumps -- close to an inch in some cases. Even at
   smaller voltage you can get arcing if your gap is small enough.

   The minimum sparking voltage for air is I believe 327 volts, so it
   should not be a problem if it is 5 volts like you say. But if the
   voltage is above that, then the air pressure and distance of the gap
   come into play. The lower the pressure, the bigger the gap that the
   current will jump, according to Paschen's Law.

   Anyway don't get me wrong, I am not against stock engines. In fact I
   think a bone-stock engine is a very good way to go for an airplane
   of modest performance. The automakers have made great strides in the
   reliability of engine computers and sensors. Most of today's
   better-built cars will wear out long before they have an ECU-related
   breakdown.

   In fact, when it comes to adapting these engines for use in
   homebuilt airplanes, the problems usually occur with the stuff that
   we add or modify -- like reduction drives, exhaust systems, fuel and
   charging systems, etc.

   I really think that an airplane designed to take a box-stock RX8
   engine and run it as is without any kind of modification or add-ons,
   would be an excellent idea. In fact, I am designing such a plane and
   intend to build and fly it. I will have some preliminary 3D drawings
   on my ductedfanaircraft group on Yahoo in a few days.

   It is a twin-boom design, like a Cessna 336 or Adam A-500, with the
   engine and duct in the back of the fuselage "stub." It will require
   no reduction drive or any add-ons whatsoever. Even the stock exhuast
   system can be used as it is pointing the right way (aft).

   The propulsive efficiency will be very close to that of a propeller
   plane, but the big advantage is you can just take a box-stock RX-8
   engine, bolt it in and fly. However, I am limiting this plane to
   12,000 feet, above which you need oxygen anyway (to be legal).

   But when we start talking about turbocharged planes and flying at
   high altitudes, it means re-engineering a lot of the supporting
   systems on the engine. At that point, it makes more sense to me to
   go with mechanical systems for fuel and ignition.


   Regards,

   Gordon.



The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.