Subject: OEM engine computer (Stock Engines in Homebuilt Planes]
From: Rotary Engine
Date: 5/4/2007, 9:23 AM
To: AARotary Engine



    Paul, and the group

    A lot has been written about aftermarket computers for our aero
    conversions. However, is there any reason why the stock engine
    computer
    can not be used? Does anyone have any experience in using
    stock? Good or
    bad? How does one go about configuring the stock unit for
    aircraft use?
    Engine is a 13b single turbo with fuel injection.

    Thanks and regards,

    --
    Erik Snyman
    Messina
    South Africa.

    Perry Mick has over 500 hours with the stock computer. There are a
    few tricks
    however. The stock computer takes in some data from certain
    places that
    don't exist in an airplane. I'll let Perry explain it if he
    doesn't
    mind.
    As I recall the big hang up is leaning it. Perry was working on a
    solution
    for that as I recall.


    ---------------------------------------------------------------------
    BTW HKS makes a bunch of add on device that change the output
    of the
    varies
    RX8 engine sensors in real time. I suspect they are basically
    PICAXEs with
    analog to digital converters that take in the sensor voltage and
    covert it to a
    different analog output voltage to be fed into the stock OEM
    computer.
    I think this is the way they did it with this 390 HP turbo RX8
    engine.
    http://www.rotaryeng.net/Turbo-RX8a.jpg

    For example if you wanted to lean the OEM computer for use at
    high altitude you would take in the mass air flow sensor output
    voltage
    and change it so the the stock OEM computer thought it was
    getting less
    air than it actually was. Consequently it would put out less fuel.
    Pretty easy to do with a $30 PICAXE.

    Paul Lamar ...No rotor no motor.


    Paul,

    I would have reservations about using an OEM computer at high
    altitudes. (Or any computer that has not been proven for aircraft
    use, for that matter.)

    The reason is that as atmospheric pressure drops, it becomes easier
    for electrical current to jump gaps and end up where it's not
    supposed to. We see this in aircraft magnetos that have arc-over at
    higher altitudes. That's why some of the turbocharged planes have
    pressurized magnetos.

    It is anyone's guess how the electronics inside an engine computer
    will behave at pressure of even half that at sea level (15,000 feet
    approx.). They may work fine, they may not.

    My own opinion is that I would rather not fly a stock engine
    computer above 10 to 12 thousand feet. At this altitude the stock
    computer should be able to handle the leaning anyway.

    For any serious flying above that, my preference is for a purely
    mechanical ignition system (flywheel magneto, a la Rotax), and carb
    or mechanical fuel injection.


    Regards,

    Gordon.

    Those are real high voltages Gordon. Not a problem at 5 volts.
    Sparks are
    20,000 volts and up.
    Most engine computers have a coating over the parts called a
    conformal
    coating which acts as an insulator. At Pikes peak in Colorado there
    is a road to the top at 14,000 feet as I recall where the
    public can and do drive to the top. Perry has had no trouble with
    this in
    over 500 hours.

    Paul Lamar ...No rotor no motor.

    Paul,

    Yes, the voltage in magnetos is very high, but so is the distance
    that the current jumps -- close to an inch in some cases. Even at
    smaller voltage you can get arcing if your gap is small enough.

    The minimum sparking voltage for air is I believe 327 volts, so it
    should not be a problem if it is 5 volts like you say. But if the
    voltage is above that, then the air pressure and distance of
    the gap
    come into play. The lower the pressure, the bigger the gap that the
    current will jump, according to Paschen's Law.

    Anyway don't get me wrong, I am not against stock engines. In
    fact I
    think a bone-stock engine is a very good way to go for an airplane
    of modest performance. The automakers have made great strides
    in the
    reliability of engine computers and sensors. Most of today's
    better-built cars will wear out long before they have an
    ECU-related
    breakdown.

    In fact, when it comes to adapting these engines for use in
    homebuilt airplanes, the problems usually occur with the stuff
    that
    we add or modify -- like reduction drives, exhaust systems,
    fuel and
    charging systems, etc.

    I really think that an airplane designed to take a box-stock RX8
    engine and run it as is without any kind of modification or
    add-ons,
    would be an excellent idea. In fact, I am designing such a
    plane and
    intend to build and fly it. I will have some preliminary 3D
    drawings
    on my ductedfanaircraft group on Yahoo in a few days.

    It is a twin-boom design, like a Cessna 336 or Adam A-500, with the
    engine and duct in the back of the fuselage "stub." It will require
    no reduction drive or any add-ons whatsoever. Even the stock
    exhaust
    system can be used as it is pointing the right way (aft).

    The propulsive efficiency will be very close to that of a propeller
    plane, but the big advantage is you can just take a box-stock RX-8
    engine, bolt it in and fly. However, I am limiting this plane to
    12,000 feet, above which you need oxygen anyway (to be legal).

    But when we start talking about turbocharged planes and flying at
    high altitudes, it means re-engineering a lot of the supporting
    systems on the engine. At that point, it makes more sense to me to
    go with mechanical systems for fuel and ignition.


    Regards,

    Gordon.

    A few issues...

    I believe that 327V applies to a 0.1" air gap. It would make sense that
    smaller gaps can be jumped by lower voltage.

    You can go to 14k' MSL without O2 here in the US.. I've actually been
    that high to get some relief from turbulence while crossing a pass on a
    windy day. Above 12.5k' MSL for more than thirty minutes requires O2.
    I wouldn't own an airplane that had any sort of equipment driven
    altitude restriction..

    As has been discussed here before, automotive emissions laws force the
    computer to run at stoichiometric mixture. Significantly better BSFC
    numbers can be achieved by leaning. If you run a stock computer the
    utility/economy of the plane can be improved if you come up with a way
    to fool the computer. You might think that the amount of time at
    partial throttle is limited, but I can think of a couple of scenarios
    where part power is used for long periods - westbound x-country is often
    flown at low altitude to minimize the impact of strong westerly winds..

    It would be relatively easy to test the function and reliability of an
    engine management computer at a simulated worst case altitude - in a
    depressurized (and instrumented) chamber.


    Matt-


    Matt, I believe 327 volts is the minimum voltage required for
    current to spark in air, no matter how small the gap size. Below
    that voltage, the electrical resistance in the air is enough to
    prevent a spark.

    Above 327 volts, the gap distance and air pressure do come into
    play. On the Mazda computer this should not be a problem,
    apparently, because it never sees more than 12 volts. But there
    are lots of capacitor discharge ignition systems that see more than
    400 volts, so with these there is definitely potential for arcing at
    higher altitudes.


    Regards,

    Gordon.


I don't think that is true Gordon. Try a 12 volt battery. Short it out and then open
the short. It will spark in air.

The Wright brothers used a set of cam driven contacts located in the combustion
chamber. When the piston got near TDC the contacts would close and open igniting the mixture.
In this situation the air pressure is higher creating a better insulator in theory.
However there was fuel vapor in there so that may have changed the insulating
properties. I am not saying a circuit board will not spark at high altitude.
Even at voltages as low as 5 volts.  I am also not saying magnetos are not
pressurized for high altitude use. They are.

Most PC boards have .025 inches between the traces. Some have .01 inches between
the traces. However when the board is coated with a conformal coating, typical
for engine computers, there is no air between the traces.

Paul Lamar

Our college physics class for engineers taught us there is a formula for
this... it starts with the assumption that 25,000 volts will jump 1" in
a vacuum and the minimum voltage drops with distance drop.  I would
think you could google this.  But even still, the coated boards insulate
against this.

-dave


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.