Subject: Racing Beat P Port Rotor housings
From: Rotary Engine
Date: 5/4/2007, 5:29 PM
To: AARotary Engine



    Do they always bore the port at an angle rather than straight from
    the side?
    Can one request a port bored from the side?
    Joe Berki

     >
     >
     > Does anyone know what diameter the P Port housings are that  RB sells?
     > ID, OD ?
     > Thanks for any help
     >
     > Joe Berki
     > Limo EZ
     >
     > My guess is BIG :) I'll forward this to Jim.
     >
     > --
     > Paul Lamar ...No rotor no motor.


    Do they always bore the port at an angle rather than straight from
    the side?
    Can one request a port bored from the side?
    Joe Berki

    I'll send that question too.

    BTW My machinist friend is boring out a junk rotor housing as we
    speak. If you want them straight in send them to him and he  will do it.
    His shipping address is:

    Jim Poole Care of:
    Light Speed Engineering
    416 E. Santa Maria Street,
    Hangar #15, Santa Paula, CA 93060

    So far he has done four and is in the process of doing another one
    for me. I just
    bought him a high quality 1-7/8 inch hole saw to speed the  process.
    I am building a
    test junk rotor housing which I will have the SS tubes trial tig
    welded to the steel liner.

    Mark Steitle is also working on this idea in Austin but I thought
    two separate efforts won't hurt. Mark is an excellent tig welder.

    If that works we are going to build up an RX8 p-port engine and  test
    it on
    the Mazdatrix dyno.

    Probably be a four port low power engine as they are probably
    cheaper than the
    six port high power version. We don't care if it has only four  side
    ports as we
    won't be using them anyway. It should idle great as it is
    a second or third gen engine in reverse. P-port intake with side
    port exhaust. Also the fuel burn should be 8% lower as the raw
    unburnt fuel is still recycled by the side exhaust ports.

    Paul Lamar ...No rotor no motor.



    Hi Paul,

    Minimum diameter - 1.713", tapering before and after. If you don't
    bore at an angle, it is much harder to seal against the inner  wall.
    Mazda factory race housings were straight in from the side.  There was
    no power difference.

    Jim Mederer

    Thanks Jim.

    Paul Lamar

    Paul,

    I really like the idea of the Renesis (RX8) engine with its side
    exhaust ports. I was just reading how the two side exhaust ports
    combined have almost double the exhaust port area of the P-port
    exhaust on the previous generation engine (13B).

    They claim the change in port timing gives a longer expansion  cycle,
    which improves thermal efficiency. I can believe that.

    Another thing I like is that it lowers the exhuast gas  temperature.
    This is especially significant for a turbo engine, where you could
    have big issues with the high exhaust temp.

    Adding P-port intakes to the RX8, idling should be very clean  as you
    say. Not to mention the extra power. Btw, I was very surprised to
    learn that the so-called "high power" six port version of the RX8
    puts out almost 250 hp at 8500 rpm.

    The P-port also simplifies the intake manifold and carburetion. I
    wonder if the Bing carbs that come on Rotaxes would be big enough?
    (One for each rotor).


    Regards,

    Gordon.

They have backed off on the 250 HP claim. It is now 232 HP.

Paul Lamar ...No rotor no motor.

On the issue of straight in vs angled p ports,  the straight in ports
give us better angles for the up and over intake.  If you start off
with the angled intake, it is immediately too high to fit under any
cowl.  Either way,  a cast, low profile  intake would help a lot.
Jerry

If the straight in  does not fit using 2 inch 180 degree tubing bends it is cheaper
and lighter to put a power bulge on the top of the fiber glass cowl on those few airplanes
that require it.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.