>> Do they always bore the port at an angle rather than straight from
>> the side?
>> Can one request a port bored from the side?
>> Joe Berki
>>
>>>
>>>
>>> Does anyone know what diameter the P Port housings are that RB
sells?
>>> ID, OD ?
>>> Thanks for any help
>>>
>>> Joe Berki
>>> Limo EZ
>>>
>>> My guess is BIG :) I'll forward this to Jim.
>>>
>>> --
>>> Paul Lamar ...No rotor no motor.
>>
>>
>> Do they always bore the port at an angle rather than straight from
>> the side?
>> Can one request a port bored from the side?
>> Joe Berki
>>
>> I'll send that question too.
>>
>> BTW My machinist friend is boring out a junk rotor housing as we
>> speak. If you want them straight in send them to him and he will
do it.
>> His shipping address is:
>>
>> Jim Poole Care of:
>> Light Speed Engineering
>> 416 E. Santa Maria Street,
>> Hangar #15, Santa Paula, CA 93060
>>
>> So far he has done four and is in the process of doing another one
>> for me. I just
>> bought him a high quality 1-7/8 inch hole saw to speed the
process.
>> I am building a
>> test junk rotor housing which I will have the SS tubes trial tig
>> welded to the steel liner.
>>
>> Mark Steitle is also working on this idea in Austin but I thought
>> two separate efforts won't hurt. Mark is an excellent tig welder.
>>
>> If that works we are going to build up an RX8 p-port engine and
test
>> it on
>> the Mazdatrix dyno.
>>
>> Probably be a four port low power engine as they are probably
>> cheaper than the
>> six port high power version. We don't care if it has only four
side
>> ports as we
>> won't be using them anyway. It should idle great as it is
>> a second or third gen engine in reverse. P-port intake with side
>> port exhaust. Also the fuel burn should be 8% lower as the raw
>> unburnt fuel is still recycled by the side exhaust ports.
>>
>> Paul Lamar ...No rotor no motor.
>>
>>
>>
>> Hi Paul,
>>
>> Minimum diameter - 1.713", tapering before and after. If you don't
>> bore at an angle, it is much harder to seal against the inner
wall.
>> Mazda factory race housings were straight in from the side.
There was
>> no power difference.
>>
>> Jim Mederer
>>
>> Thanks Jim.
>>
>> Paul Lamar
>>
>> Paul,
>>
>> I really like the idea of the Renesis (RX8) engine with its side
>> exhaust ports. I was just reading how the two side exhaust ports
>> combined have almost double the exhaust port area of the P-port
>> exhaust on the previous generation engine (13B).
>>
>> They claim the change in port timing gives a longer expansion
cycle,
>> which improves thermal efficiency. I can believe that.
>>
>> Another thing I like is that it lowers the exhaust gas
temperature.
>> This is especially significant for a turbo engine, where you could
>> have big issues with the high exhaust temp.
>>
>> Adding P-port intakes to the RX8, idling should be very clean as
you
>> say. Not to mention the extra power. Btw, I was very surprised to
>> learn that the so-called "high power" six port version of the RX8
>> puts out almost 250 hp at 8500 rpm.
>>
>> The P-port also simplifies the intake manifold and carburetion. I
>> wonder if the Bing carbs that come on Rotaxes would be big enough?
>> (One for each rotor).
>>
>>
>> Regards,
>>
>> Gordon.
>>
>> They have backed off on the 250 HP claim. It is now 232 HP.
>>
>> Paul Lamar ...No rotor no motor.
>
>
>
> Paul,
>
>
> Yes and Jim at Racing Beat will tell you it is even less than
232HP. I
> wonder about your hopes for good idling performance. With a
P-port intake
> there would once again be an overlap before the side exhaust port
closes
> right? Good luck with this test.
>
> Doug Fir
>
> Why do you think that? It is, in effect, exactly like a second
gen or third
> gen engine. Two side ports and one peripheral port except they
are reversed.
> Exhaust is side port and intake is peripheral.
>
> What causes the bad idle is the direct connection between two
peripheral
> ports. One exhaust and one intake.
>
>
> Paul Lamar ...No rotor no motor.
Paul,
You are correct. Sorry I mis worded my question. I meant to say the
overlap
like the second and third gen will also introduce some exhaust into
the
intake negatively affecting the BSFC.
Doug Fir
I don't think that affects the BSFC at medium to high power. It mainly
affects the freq. of misfire rate at low power near idle. See the
attached charts.
IMHO the main reason the RX8 eng. gets 8% better BSFC at high to
medium power
is the unburned HCs are kept in the engine and recycled. That will
not change
with a P-port RX8 engine. The side exhaust port RX8 engine is all
about low power
torque and idle characteristics. In other words the realm of the car.
--
Paul Lamar ...No rotor no motor.
Paul,
What about the port timing? Do you accept as valid that the later
opening of the exhaust port on the side-port engine affords a longer
expansion cycle and therefore better thermal efficiency?
Also, on the RX8 there is no overlap between the intake and exhaust
port timing at all, right? So if you p-port the intake, there will
be some overlap? How will this affect efficiency in the high-rpm
range that is relevant for us in aircraft use?
Regards,
Gordon.
That probably helps a little. As I said the lack of over lap has more to
do with idle than anything else. Actually on balance I would say
the side exhaust ports probably add a wee bit of back pressure.
--
Paul Lamar ...No rotor no motor.
Gordon ,
I'm not going against anything Paul has said, however if I could add a
little in saying, I asked the same sort of questions of mechanical engineers
and their answer was that that most engines tolerate some overlap (can't
remember the degrees exactly). So the overlap of the RX7 is in line with
this tolerance. I can't imagine the P-port being any worse in the RX8,
although I haven't sat down and tried to work it out in degrees. We are
speaking here primarily about idle as the higher RPM eliminates
contamination, as the exhaust is self evacuating at the higher exhaust
speed/RPM. In fact it's more likely to suck in some inlet charge at higher
RPM.
George (down under)
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.