>> > Hello
>> >
>> > I am now the owner of this rotary engine that was made by
>> Yaw
>> power. It is
>> > installed in my newly acquired Merlin GT. The aircraft has
>> never
>> been flown
>> > and
>> > the engine has 0 hours on it. To make a long story short
>> I have
>> limited
>> > knowledge on rotary and I need all the help I can get.
>> >
>> > Thanks
>> >
>> > Ron Anderson
>> >
>> >
>> > I added you to the list Ron so ask any question you wish no
>> matter
>> > how dumb you might think it is. There are no dumb questions
>> > on here.
>> >
>> > BTW Since the Merlin GT is an ultra light I assume the
>> engine
>> > you bought from Paul Yaw was a one rotor. Even the one rotor
>> > Mazda engine is a bit heavy for this airplane.
>> > --
>> > Paul Lamar ...No rotor no motor.
>>
>>
>> > I agree and I may have to replace it, but it came mounted in
>> the
>> plane so
>> I think I'm going to try it first. Other Merlins at Blue yonder
>> Aviation are
>> flying with O 200s, I think they are about 200lbs. And yes
>> it is
>> a
>> one rotor
>> engine and I have no idea how much it weighs, and it is the
>> same
>> engine that is
>> in the picture. Paul paints his engines blue and the red was
>> a one
>> of special
>> request.
>>
>> 1st question (all my questions will be dumb. sorry)
>>
>> What type of electronic fuel pump would you recommend and how
>> much fuel
>> pressure is required for a one rotor
>>
>> 2. Any special way to plumb the engine to avoid excessive heat?
>> 3. Any special type of exhaust system needed?
>> 4. what would be normal temps and oil pressure readings?
>>
>> Thank you for repleying
>>
>> Ron Anderson
>>
>>
>> >
>>
>> 1. I like the MSD or Carter rotary vane fuel pumps.
>> Not Walbro.
>>
>> 2. Yes of course. The rad and oil cooler ducting and sizes of
>> rad and
>> oil cooler must be correct. This adds weight of course.
>> You will need a rad of about 300 cubic inches and an oil cooler
>> around 120 cubic inches. The larger the frontal area the
>> better.
>> In other words 20" by 20" by 1" thick is better than 10" by 10"
>> by 4"
>> thick. Get my cooling book from AC Spruce.
>>
>> 3. Exhaust design is not important but use .065" wall 321 SS on
>> the
>> first
>> third or half of the exhaust. Do Not use mild steel.
>>
>> 4. Try to keep the water and oil below 200 F. 220 F water and
>> oil is OK
>> for awhile but not recommended.
>> --
>> Paul Lamar ...No rotor no motor.
>>
>>
>> Somehow I thought it was 300 cu-in for a 13b and that a single rotor
>> would be less. Ron's engine is a single.
>>
>>
>> Regards,
>>
>> Matt-
>>
>> 600 cubic inch for a 13B minimum. More is better.
>>
>> Paul Lamar ...No rotor no motor.
>>
>>
>>
>> Thanks Paul.. I remembered wrong.
>>
>> I can see why you state it the way you do. 300 cu-in / rotor is a more
>> useful metric.
>>
>>
>> Matt-
>
> Thanks for all the input but I'm afraid Paul is right, the
> engine is just too heavy for this type of aircraft. I do appreciate the
> wealth
> of knowledge that resides at this forum. Unfortunately after weighing the
> engine, I have no other choice but to replace it. If anyone is
> interested in
> purchasing the engine give me a yell. Thanks again for your help.
>
> Good Luck to all and safe flying
>
> Ron Anderson
What did the engine weigh? With or without reduction?
How much do you want for it?
Where are you?
If you are going to mount an O-200, you need to uprate your airframe.
The specs which were posted included a note that the plane has a
challenge with heavy engines.
Keith Wood
Hello Keith
Engine weight unknown (210 - 220lbs) just got the plane so I don't know for sure
Sold With the reduction unit made by Ross Aero
Engine resides in Calgary Alberta Canada
Price unknown - I just need it to be fair
Motor mounts included
Electronic ignition included
There is no exhaust manifold
Ron Anderson
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.