Subject: Second steel tube P-port successfully welded.
From: Rotary Engine
Date: 6/4/2007, 4:34 PM
To: AARotary Engine


         This was done by Matt who is the race car chassis builder
         at Mazdatrix. It had some aluminum removed around the
         steel liner where it was welded to the 304 SS .065 wall tube.
         As Mark Steitle discovered this is totally unnecessary.

         Removing aluminum is difficult to do and labor intensive as
    compared
         to just welding it in.

         It took Matt about five minutes to weld this and I paid him $22
    bucks.

         Welding them in is not completely necessary but it gives another
         level of security against coolant leaks.

         Sure is quick and easy to do. I am going to do it on
         the RX8 P-port engine.

         Paul Lamar ...No rotor no motor.



    I gather that grinding the weld down so that it won't interfere with
    the
    apex seal going by is also trivial..  Does it need to be ground away
    such that the seal never rides over a region where the weld heat has
    altered the liner's physical properties?  Or is the metallurgy of the
    welded material okay?  I realize you might not have enough data to
    answer that.

    After welding to the liner, is it then only necessary to seal the tube
    along the outside of the housing?  Or are there other interfaces that
    also need sealing?

    Sorry, but another dumb question:  Does this process eliminate the need
    to do that pressurized application of JB Weld, or is it still required
    for other places on the tube (where the tube exits the housing on the
    outside)?


    Matt-

    First question about the material properties is right. Long time
    wear is unknown.

    Yes it is only necessary to seal the outer part of the water
    jacket around the steel tube. I will still do that in pressurized
    stages to insure there are no leaks.

    --
    Paul Lamar ...No rotor no motor.


Please allow me to muddle around with this a little more Paul..

Can aluminum tube be welded to the cast aluminum portion of the
housing?  If so, how about weld a piece of steel tube to the liner and
an aluminum mounting boss to the aluminum portion of the housing?  The
end of the steel tube could have a flat for a seal/o-ring/gasket/RTV of
some sort.  Then weld a piece of Aluminum tubing (with a mounting flange
for the slide throttle) to the outside of the housing.

The process would go like this:

1.  Bore a whole just large enough to accept a short length of steel
pipe which will be welded to the liner.

2.  Step bore a piece of steel pipe so that it has a short slip fit
joint on the end away from the end which will be welded to the liner.
Probably use relatively thick wall..

3.  Weld the pipe into the liner of the housing.  To jig the weld,
insert a longer piece of pipe through the hole in the outside of housing
into the step in the tube to be welded to the liner.  The jigging tube
needs to have a step on the outside cut so that the two pieces of steel
tube fit together with about a 1/4" overlap.

4.  Build up the aluminum tube with flange on the end.  The ID of the
aluminum tube should fit the OD of the steel tube.  The length of the
aluminum tube is not critical - just so that it extends through the
outer portion of the housing.

5.  Bore the aluminum portion of the housing large enough to fit the OD
of the aluminum tube.

6.  Insert the aluminum tube, jigged in place with a length of steel
tube to fit the steel tube already welded to the liner.

7.  Cut the steel tube to length at the end of the aluminum
flange/mounting boss.

8.  RTV the pieces of steel tube together, and from the tube to the
aluminum flange.


Instead of welding the aluminum together, you could stay with JBWeld,
but for those that wish for a different solution, this would work..  It
should provide a solid method of construction and sealing, and is
probably pretty repairable (should the need arise).


Matt-

Matt,
I have a better solution, however similar to your, I came up with it last
night.
Use Paul's method to weld in the piece of SS to the liner.
Weld in an aluminum insert the other side which fits neatly over the steel
tube.
The flange can screw to the insert (which has pre drilled and tapped holes)
the flange which screws to the aluminum inset has a recess to take the
steel tube and an O ring to clamp against the welded insert.

If you then want to seal the cavity you still can, but any future leaks will
be around the O ring which can be replaced.

Now that's an elegant solution - even if I do say so myself.
George (down under)


All this stuff requires machine tools.  At least a lathe while
JB Weld works with just hand tools. I am trying to make this cheap
and easy to do.

-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.