This design steals ideas from Ellison and Mikuni.
The fuel metering is done with a bunch of small holes
drilled into a brass tube that stays in the air passage
all the time similar to the Ellison. The slide is three piece
similar to the Mikuni 48 mm. As the slide opens it exposes more
and more small holes in the brass tube increasing the fuel flow.
The brass tube is attached to a stationary rectangular column
that is fixed to the spacer. The fuel comes in through the
spacer and down the column to the brass tube. The brass tubes
fit in holes in the center parts of the slides. The fuel is
sucked out of the side of the tube by the Coanda effect.
Ellison claims excellent atomization.
The trade off is a more complicated slide.
However it is much lower technical risk than the ramp in the Teflon idea
as it uses a tried and true method of metering fuel. There are
hundreds of
Ellisons out there on all sorts of airplanes. It does not use the
Ellison method
of leaning the mixture. The mixture is still leaned with the
external fuel pressure regulator. The Ellison of course has a built
in fixed fuel pressure regulator.
It is a bit hard to tell what is going on here by looking at these
3Ds. One has a solid slides and the other transparent slides. Both
are shown
in all three positions. Closed, half open and fully open from
top to bottom.
This is my fall back option if the ramp in the slide idea does not
work.
Why not use a couple of Ellisons? That will work if you don't mind
paying $825 each.
For a lot more on how the Ellison works check out the web site:
http://www.ellison-fluid-systems.com/
---------------------------------------------------------------------------
Here is a blatant dual copy of the Ellison. Nobody will be able to
build it
and sell it as Ellison has a good patent on it I am sure. That will not
stop an individual from building one for himself.
The 1/8 dia. brass tube runs all the way through the 3/8 thick one piece
Teflon slide. It is not easy to machine so be aware.
BTW I gave up on this multiple hole idea because one could not
insure the mixture would not vary between holes. Here is what Ben
Ellison
has to say on the subject.
"The TBI uses a tube with many holes to meter fuel in the
venturi. This tube is
covered by a slide valve used for the throttle. At low power
settings, which
are common in auto applications but not in aircraft, the fuel
metering steps
from slightly lean to slightly rich as the throttle is opened. This
variation
in mixture results in poor fuel economy as well as illegal levels of
exhaust
emissions. Aircraft, on the other hand are always above 50% power
and the
digital nature of the fuel metering is irrelevant."
So he changed my mind :)
Paul Lamar ...No rotor no motor.
Paul wrote:
"Nobody will be able to build it and sell it as Ellison has a good
patent on it I am sure."
Where is the legality of custom building parts for a system that
customers assemble according to plans.
I wonder if Mr Ellison would allow use of the technology for this
application. He may have a patent, but be willing to license (possibly
for a small fee). Some people make a tidy income from licensing their
patents.
I like this system, but wonder about the flow efficiency of the fuel
delivery tube as compared to a conventional throttle butterfly (when
WOT). How much of the benefit of the slide throttle are we losing?
Matt-
I don't know the legal ins and out. I guess if you sold a brass tube with
a bunch of holes in it nobody could sue you and win.
No doubt we are losing some. It is all a trade off between technical risk
verses maximum efficiency. Also money for R&D is a large factor.
BTW Ellison uses materials in his carb that are incompatible with
auto fuel. We are using an ordinary automotive fuel pressure regulator that IS
compatible with auto fuel.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.