Subject: Ellison style dual slide throttle LPFI
From: Rotary Engine
Date: 6/5/2007, 8:07 PM
To: AARotary Engine


     > This design steals ideas from Ellison and Mikuni.
     > The fuel metering is done with a bunch of small holes
     > drilled into a brass tube that stays in the air passage
     > all the time similar to the Ellison. The slide is three piece
     > similar to the Mikuni 48 mm. As the slide opens it exposes more
     > and more small holes in the brass tube increasing the fuel flow.
     > The brass tube is attached to a stationary rectangular column
     > that is fixed to the spacer. The fuel comes in through the
     > spacer and down the column to the brass tube. The brass tubes
     > fit in holes in the center parts of the slides. The fuel is
     > sucked out of the side of the tube by the Coanda effect.
     > Ellison claims excellent atomization.
     >
     > The trade off is a more complicated slide.
     > However it is much lower technical risk than the ramp in the
    Teflon idea
     > as it uses a tried and true method of metering fuel. There are
    hundreds of
     > Ellisons out there on all sorts of airplanes. It does not use the
    Ellison
     > method
     > of leaning the mixture. The mixture is still leaned with the
     > external fuel pressure regulator. The Ellison of course has a built
     > in fixed fuel pressure regulator.
     >
     > It is a bit hard to tell what is going on here by looking at these
     > 3Ds. One has a solid slides  and the other transparent slides.
    Both are shown
     > in all three positions. Closed, half open and fully open from
     > top to bottom.
     >
     > This is my fall back option if the ramp in the slide idea does
    not work.
     >
     > Why not use a couple of Ellison's? That will work if you don't mind
     > paying $825 each.
     >
     > For a lot more on how the Ellison works check out the web site:
     > http://www.ellison-fluid-systems.com/
     >
     >
    ---------------------------------------------------------------------------

     > Here is a blatant dual copy of the Ellison. Nobody will be able
    to build it
     > and sell it as Ellison has a good patent on it I am sure. That
    will not
     > stop an individual from building one for himself.
     > The 1/8 dia. brass tube runs all the way through the 3/8 thick
    one piece
     > Teflon slide. It is not easy to machine so be aware.
     >
     > BTW I gave up on this multiple hole idea  because  one could not
     > insure the mixture would not vary between holes. Here is what Ben
    Ellison
     > has to say on the subject.
     >
     > "The TBI uses a tube with many holes to meter fuel in the
    venturi.  This tube
     > is
     > covered by a slide valve used for the throttle.  At low power
    settings, which
     > are common in auto applications but not in aircraft, the fuel
    metering steps
     > from slightly lean to slightly rich as the throttle is
    opened.  This variation
     > in mixture results in poor fuel economy as well as illegal levels
    of exhaust
     > emissions.  Aircraft, on the other hand are always above 50%
    power and the
     > digital nature of the fuel metering is irrelevant."
     >
     > So he changed my mind :)
     >
     > Paul Lamar ...No rotor no motor.

    Paul,


    I see you have come a full circle. If you want to go with an Ellison
    type of
    spray pipe why don't you just insert it into the intake manifold
    downstream
    of the slide throttle?


    Doug Fir

    Then you would not be able to close off the tiny holes.
    You need a way of doing that proportional to the amount of air
    going in the engine.

    This is a very simple and well proven system. Very cheap too if you
    can make it your self. Much easier to drill .016 dia. holes in it than
    at the bottom of a long hole in Teflon. Still rather labor intensive
    in case you don't have an NC mill. If a bunch of people are interested
    I may have a batch of the tubing with holes  made up.

    I'll work on the 3Ds some more and it may become
    clearer. It is also very adaptable to Doc's version of the slide
    throttle.

    --
    Paul Lamar ...No rotor no motor.


Can we just buy the tube from somebody already made?  Would Ben Ellison
sell them to us?  Might be fairly cheap?

Laser cut would be slick (like the weeping leading edge on the wing of a
Cirrus)..

http://www.ebteccorp.com/lasercut.html

Is there a gradient to the number of holes?  In other words, does the
number of holes per unit length differ at the idle portion as compared
to the WOT portion?


Matt-

It could. Probably be a function of the actual area that was open for the air.
Also of course the size can vary. I have a friend that has one off his
airplane I'll take a closer look. Ellison's tube is not near as long as the
one we will need. Overall length on ours will be about 13 inches.
The tubing comes in six foot lengths for about $10.

The trick is drilling the 1/8 inch dia. hole in the 9.7" long Teflon slide straight.
It is best to start with a short drill and keep changing drills for longer
and longer ones. Also it may be better to drill from both ends and have them
meet in the middle. Too bad you can't buy a gun drill with a 1/8th inch
bore.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.