> This design steals ideas from Ellison and Mikuni.
> The fuel metering is done with a bunch of small holes
> drilled into a brass tube that stays in the air passage
> all the time similar to the Ellison. The slide is three piece
> similar to the Mikuni 48 mm. As the slide opens it exposes more
> and more small holes in the brass tube increasing the fuel flow.
> The brass tube is attached to a stationary rectangular column
> that is fixed to the spacer. The fuel comes in through the
> spacer and down the column to the brass tube. The brass tubes
> fit in holes in the center parts of the slides. The fuel is
> sucked out of the side of the tube by the Coanda effect.
> Ellison claims excellent atomization.
>
> The trade off is a more complicated slide.
> However it is much lower technical risk than the ramp in the Teflon
idea
> as it uses a tried and true method of metering fuel. There are
hundreds
of
> Ellisons out there on all sorts of airplanes. It does not use the
Ellison
> method
> of leaning the mixture. The mixture is still leaned with the
> external fuel pressure regulator. The Ellison of course has a built
> in fixed fuel pressure regulator.
>
> It is a bit hard to tell what is going on here by looking at these
> 3Ds. One has a solid slides and the other transparent slides. Both
are
> shown
> in all three positions. Closed, half open and fully open from
> top to bottom.
>
> This is my fall back option if the ramp in the slide idea does not
work.
>
> Why not use a couple of Ellisons? That will work if you don't mind
> paying $825 each.
>
> For a lot more on how the Ellison works check out the web site:
> http://www.ellison-fluid-systems.com/
>
-------------------------------------------------------------------------
-
-
> Here is a blatant dual copy of the Ellison. Nobody will be able to
build
> it
> and sell it as Ellison has a good patent on it I am sure. That will
not
> stop an individual from building one for himself.
> The 1/8 dia. brass tube runs all the way through the 3/8 thick one
piece
> Teflon slide. It is not easy to machine so be aware.
>
> BTW I gave up on this multiple hole idea because one could not
> insure the mixture would not vary between holes. Here is what Ben
Ellison
> has to say on the subject.
>
> "The TBI uses a tube with many holes to meter fuel in the venturi.
This
> tube is
> covered by a slide valve used for the throttle. At low power
settings,
> which
> are common in auto applications but not in aircraft, the fuel
metering
> steps
> from slightly lean to slightly rich as the throttle is opened. This
> variation
> in mixture results in poor fuel economy as well as illegal levels
of
> exhaust
> emissions. Aircraft, on the other hand are always above 50% power
and
the
> digital nature of the fuel metering is irrelevant."
>
> So he changed my mind :)
>
> Paul Lamar ...No rotor no motor.
Paul,
Looking at this drawing again, it looks like the tube + the slide, is
being
drawn back from the opening.
It would be better if the tube was FIXED in place with a fixed centre
strip,
with the sliding part of the Teflon covering the holes from the Left
of
the
drawing .
This could be better achieved if the tube was encapsulated by the
Teflon,
centre strip.
The Teflon would then be in two pieces, with the outer Teflon sliding
parallel with the fixed centre strip - the outer Teflon would then
cover
the
holes from the LHS. The Teflon could be shaped to form a zero opening
as
the
two sides (of the opening) close on each other.
Hope that makes sense.
George (down under)
Unnecessary. the tube is fixed at one end to the housings.
I am working on some improvements to make it easier to make.
It also will work better with Doc's slide throttle as it is.
-----------------------------------------------------------
Here are some better illustrations. Feed the fuel from the left
end of the brass tube. The holes in the tube where it is used to
feed the second rotor will be slightly larger
to equalize the fuel flow to each rotor. The brass tube can
be twisted 90 degrees to lean exactly the same way Ellison
is doing it.
We still have an external adjustable regulator to
control the over all flow and provide extra fuel for starting.
That is the only way this system deviates from the way Ellison
does it.
Paul Lamar ...No rotor no motor.
If the Ports are being fed in series via the tube won't one rotor get
more
fuel than the other? Just curious.
Joe Berki
Limo EZ
Not completely in series. More like a slight pressure drop along
the length of the tube. That is why the second rotor has larger
holes. How much larger is open to speculation at this point.
Here is a little physics experiment. Get two small six inch square
pans. Get a one foot length of porous drip irrigation tubing. Block off one
end. Feed the other end from a garden hose. Compare the volume of the
water in both pans after an hour or so.
If this drip irrigation tubing would work with gasoline I would use
it in the slide throttle :)
Paul Lamar ...No rotor no motor.
Actually Paul Joe is right.
If you want to run low pressure the feed location WILL matter.
The method would be to feed both ends of the tube if possible.
I have done several single end feed systems and the hole sizes
need to be adjusted to the available pressure. IE bigger holes
farther from the feed.
Bill Jepson
I think I said that :) Did I say anything about how much water
was in each pan? :)
Feeding it from both ends is a LOT more trouble as you will see
shortly. Varying the holes size along the tube is a lot more practical.
--
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.