Subject: Ellison type tube hole patterns and sizes
From: Rotary Engine
Date: 6/13/2007, 8:27 PM
To: AARotary Engine



              I calculated the air opening area of the slide in .2 inch
   travel
              increments.
              I then attempted to match the fuel flow to the slide
   opening area.
              Roughly speaking it takes 27 .013" dia. holes variably
   spaced
              along the tube. Each hole passes enough fuel for 4.45 HP at 2
        psi so
              27 holes is 120 HP per runner. 240 HP for the p-port engine.

              As Ben Ellison says this causes a stepped ramp digital
   supply
        of fuel.
              In other words the engine goes from rich to lean and back to
        rich as
              the
              slide moves. The problem is severe in the first one third
              travel of the slide throttle. Ellison largely got around
   this by
              using much
              smaller holes and many more of them. My guess by looking at
        them is
              they can be
              as small as .1 mm or around 6 thousands of an inch. He
        probably has
              close to 100 holes in his tubes.

              BTW I can't for the life of me figure out how they can make a
        drill that
              small but they do. Airgas sells them for $45 each.

              More, much smaller holes, soon becomes a problem in a single
        row as
              the holes
              get too close together. Two or more staggered rows are
   used in the
              Ellison.
              The first 3rd are a single row. The next third  is a
   staggered
              double row and the last
              third is a staggered triple row. None of this is shown on any
              Ellison websites.
              Of course this further increases the cost.

              I talked to a friend of mine that owns an NC shop here in
   Santa
              Paula that
              has experience drilling small holes. He says there must
   be a close
              fitting
              brass rod in the  brass tube or drill breakage occurs
        frequently. At
              $45 a crack
              you don't want this to happen. Then you have the problem of
        pressing the
              sacrificial brass rod out of the nine inch long 1/8 inch
   diameter
              tube. Not
              an easy thing to do. That too requires special tooling that
        supports
              the outside
              of the tube. Perhaps this can be done better with a laser.

              I can see why Ellison is charging $850 for his aircraft
   carbs.
        It is
              also rapidly
              talking me out of this approach. Not a show stopper yet
        however as I
              have
              yet to investigate the laser option.

              -----------------------------------------------------------

              I am sure this outfit can do the job. I'll know more
   about the
        cost
              on Monday.
               http://www.calasers.com/gallery.html
   <http://www.calasers.com/gallery.html>

              --
              Paul Lamar ...No rotor no motor.

        I got a price on the tiny holes from the laser guys in Simi Valley.
        $250 minimum set up charge. Too much for me for R&D.

        I talked to Klaus about how his Ellison has worked and he thought
        it was not bad but the venturi part of it restricted
        the airflow compared to his EFI setup on his O-200. I assume he has
        a custom throttle body on there now. He got more HP with the
   custom
        throttle body.

        Here are some pictures of the Ellison carb he took off.

        Klaus also mentioned that the exact  time the fuel was squirted in
        was critical
        on a 2500 RPM aircraft engine (+/- 30 degrees) but he agreed
   with me
        that it matters
        not on a 7500 RPM engine. Another hidden advantage of the rotary.

        The next 3D is the mechanical low pressure fuel injection I am
   going to
        spend my R&D budget on. Both Hurant Karribian and I will be
   working
        on essentially
        the same thing.

        The pressure regulator soak in 100LL gasoline was successful. I
        could see no
        deterioration in the air pressure regulator plastic parts. Of
   course
        that
        is 100LL auto fuel with alcohol could be another matter.

        BTW I did some further test on JB Weld by thinning it with 25%
   acetone
        and it became very easy to pour. It set up but I can't vouch
   for the
        strength as I did not test it. With a welded in SS P-port tube
        we don't need the strength so sealing becomes its only function.

        Paul Lamar ...No rotor no motor.

   Couple of questions..

   Instead of a sequence/pattern of holes, can a varying width slot be made
   to work?  Might be essentially the same cost to cut, but maybe not...

   OR!!!  How about this?  Instead of one tube with tiny holes, how about
   two tubes - one which slips inside the other.  A series of larger holes
   (of shape yet to be imagined) in each.  Depending on how the holes are
   oriented to each other controls the mixture.  The holes could be pretty
   large (easy to drill).  Rotating one tube inside the other restricts the
   amount of fuel from 0-100%..  I'm pretty excited about that idea...  I
   want patent rights on this one.  Hah!  :)

   On the MAF sensor you picked up:  I can't remember of those use a
   heated
   mesh to measure flow, or just a (couple of) wire(s)..  I wonder how much
   obstruction there..


   Matt-

   I was going to vary the depth of the slot as the feed hole in the
   spacer is
   a limited diameter. The feed hole dia. is .0625 so the Teflon slot
   width is also .0625. Now if you can get a mill smaller than
   that we could vary both the width and the depth.
   A thin slitting saw could also be used to cut the slot.

   One drawback to laser punched holes is they leave a bit of flash
   around the edges. If you have one tube inside another that might
   be a problem. Also, as Bill Jepson pointed out, the hole sides are
   tapered.
   In a wall of .020" thick the inner hole dia could be .008 but the
   outside
   diameter of the same hole would be .014. Not a good thing I suspect.

   The mass air flow sensor had two heated wires in a bridge circuit I
   think.
   The obstruction is considerable but then again the cross sectional area
   is over kill.

   Paul Lamar ...No rotor no motor.

Okay, so use fewer but larger conventionally drilled holes..  Or pass a
brush through the outer tube to remove the flash.  Or acid etch it..

Matt-

I am going to work on the Teflon ramp. Cheaper.

Paul Lamar


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.