Subject: Mazda fuel low level warning probe
From: Rotary Engine
Date: 6/20/2007, 7:08 AM
To: AARotary Engine


> Gents,
>
> I'm using a stock Mazda fuel pump and assembly in my feeder
> tank. A
> fuel low
> level warning probe is part of the assembly holding the fuel
> pump. It's normally extended down to the bottom of the car's
> fuel tank.
> I've bent
> it up to give me an indication when the feeder tank is NOT full.
> The probe has one wire that comes out of it to the top plate
> of the
> assembly. I put my multimeter on the wire and on a ground
> (since I
> didn't
> know where else to put it and selected OHMs on various
> scales. I
> dipped the
> probe in and out of a can full of gas without any
> indications on the
> multimeter. If the probe is a switch, doesn't it need two wires?
> What makes
> this probe work?
>
> Thanks,
> Sandy McNabb
> Glass Goose with Rotor
>
> Good question. I have never ever seen one. If it is anything
> like the low
> oil level sensor it is a reed switch with a magnet float.
> http://en.wikipedia.org/wiki/Reed_switch
> <http://en.wikipedia.org/wiki/Reed_switch>
> One wire is grounded to the chassis.
>
> Sometimes the level sensors are pots on the end of a float arm.
> That will require two wires.
>
> Take some pictures.
>
> Here is the aircraft way of doing it.
>
> Paul Lamar ...No rotor no motor.
>
>
> If you are looking for a sensor that will indicate when your
> feeder tank is
> not full, you might want to consider the product shown at
> this web
> page: http://www.aircraftextras.com/LowOilSensor.htm
>
> Although it is promoted as a low oil level sensor, it works
> equally well in
> fuel or water. The optional blinking LED setup is needed to
> have a
> panel
> warning system that comes on when the fluid level drops
> below the
> top of the
> float.
>
> Rogers, Bob J.
>
> Paul, Bob, et al,
>
> I've attached two pictures of the probe.
>
> Thanks for the web site for the oil level sensor. However, I
> need a
> sensor/probe that will attach to the top of the tank to
> sense lack
> of fuel
> at that location so I can be warned when the tank is NOT
> full. If I
> can't
> figure out the Mazda probe works, then I'm thinking about
> using a
> sensor
> normally used in house security systems that activates with a
> magnet. I'd
> have to evaluate how it would hold up in fuel. Other than
> that, it is
> completely sealed.
>
> Thanks, Sandy
>
> Could be a capacitance type.
>
> Paul Lamar
>
> Sandy,
> I used a the GEMS sensors. It uses a prism lense that reflects
> when the
> prism is submerged and doesn't reflect when it isn't submerged. I
> wanted it
> to tell me when fuel in the tank was low (7 gal.). It works great
> and is
> simple to install.
>
> Mark St.
>
>
> Mark,
>
> That's perfect! And, they have several others that should work
> well also.
> Thanks for the tip.
>
> Sandy McNabb
> Glass Goose with Rotor


If you want to do it really simple, just embed a thin plexiglass tube
inside the wall of the tank, with a floating magnet inside, and epoxy a
$0.50 magnetic reed switch on the outside.  When the magnet floats down
to a target position, the switch is closed.  Another $1.00 for a
blinking LED gets you the warning light.

Scott Gettings

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.