Subject: Calculating the stress on the sun gear PSRU shaft.
From: Rotary Engine
Date: 6/21/2007, 11:30 AM
To: AARotary Engine



    >> I am stuck on a design problem.  Do you happen to know the
   formula for
    >> calculating torque strength of the drive pinion shaft that goes
   from the
    >> transmission into the clutch?   In my case with the RX-4
   intermediate
    >> housing I have a 3/4" hardened steel shaft that goes into a torque
    >> converter.   It is hard to imagine this shaft would be able to
   carry the
    >> load essentially directly coupled to the engine flex plate on
   one end and
    >> the PRSU on the other.
    >>
    >>
    >> It is also baffling how people are putting 350 or more
   horsepower through
    >> this shaft into the transmission.   I am assuming on the car the
   clutch
    >> helps a lot whereas on an airplane the shaft would experience
   more stress
    >> because of the huge prop flywheel. Assume minimal design load is
   350hp and
    >> 220 ft. pound. and a four inch long shaft.  It would be very
   similar to what
    >> Buly had to contend with a request for a longer than normal sun
   gear shaft
    >> for Tracy's PSRU. mounted to his Cosmo auto tranny.
    >>
    >>
    >> Thanks
    >>
    >>
    >> Doug
    >>
    >>
   http://physics.uwstout.edu/Statstr/statics/Torsion/tors51.htm#Topic%205.1:%2
   0>> T
    >> orsion:
    >>
    >> max stress = T R/J
    >>
    >> where T (inch pounds) is the internal torque in that section of
   the shaft,
    >> R = maximum radius of the shaft(inches), and J = polar moment of
   inertia.
    >>
    >> J = (Pi/32) d^4 for a solid shaft, and J = (Pi/32)(do^4 -di^4) for a
    >> hollow shaft, where do = outer diameter and di = inner diameter.
   In inches.
    >>
    >> Notice there is nothing about length.
    >>
    >> Paul Lamar ...No rotor no motor.
    >>
    >
    > Paul
    >
    > Here is another better site for a possible source of custom high
   strength
    > PSRU sun gear shafts or even custom ordered output prop shafts.
    >
    > http://www.marlincrawler.com/htm/axles.htm
    >
    > Doug Fir
    >
    > Those are too small Tracy uses a AA fuel dragster rear axle
   forging for the
    > prop
    > shaft.
    >
    > Paul Lamar ...No rotor no motor.

   Paul,

   Yes they are small for a prop shaft but perhaps they have the ability to
   make a custom prop shaft.  I need something on order of 3" in OD. It
   will no
   doubt become a thick pipe to cut down on weight.

   I was thinking they may something in the 1 inch or 1.135" dia
   category for
   the sun gear to engine connection.

   Doug

   Custom prop shaft/flange forgings are big bucks. Keep looking.
   Someone some where may have one. Especially in the truck or heavy
   equipment market.

   The input shaft torsional has little to do with it as it is only
   about 200 foot pounds and rather short. The gear, clutch plate and
   spline stiffness has
   a lot more to do with the resonant condition at 1800 RPM. If you use
   Tracy's isolator
   design with soft rubber bushings you can get it down below 1000 RPM.

   The prop shaft must deal with up to 600 foot pound bending due to
   gyro loads caused by rapid shifts in yaw and pitch. A stall would
   results in
   a pitch rate of about one radian per second. That is 57 degrees per
   second.
   (roughly Dave Mc :)) That is why you need a 2 inch or larger dia
   prop shaft.
   It is not the torsion. It is the bending.

   Paul Lamar ...No rotor no motor.


I'd like to see the components designed to survive snap-rolls and
tumbling maneuvers...


Matt-

2 something is the dia, of the Lyc aerobatic engine.
And that is with a 50 pound prop.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.