Subject: Cross counter flow rads
From: Rotary Engine
Date: 6/26/2007, 11:53 AM
To: AARotary Engine



        > C&R built mine from drawings I sent them. The tanks are about
2"
       thick
        > and the cores are standard, I think 1.25" thick. Might be
metric.
        > This would make the space between the two cores approx.
0.75".
        >
        > Perry
        >
        > When did you send them dwgs Perry? I know it is in the
airplane
        > but did you take any pictures before you put it in there?
        >
        > Paul Lamar ...No rotor no motor.

       I installed the psru and prop December 2004. I knew I need more
rad
       since I was developing more power, but it was fine for the
winter. I
       ordered the new rad early 2005. I sent them the 3D view that you
have,
       with overall dimensions of 13.5 inches wide by 17.5 inches long.
The
       ports are 1" NPT, on the right side forward faces of the dual
tanks at
       the front. Ideal for connecting to the waterpump, as shown on
the page
       http://www.bridgingworlds.com/LEZ13B/LEZ13B.htm. I know it took
them a
       couple months to get started on it, they said they were busy. By
       April-May 2005 I had to call them a few times to get it moving,
as I
       wanted it installed for summer flying. I think I received it by
May 17
       2005 because I have a sketch drawing with that date (screen
capture
       attached), showing how I had to make the inlet ramp much longer,
and
       move the rad aft, because the overall rad thickness increased
from 2" to
       4". Unfortunately I didn't take any photos at the time, I was in
a bit
       of a rush to get it installed because of the warm weather and a
trip to
       Kansas July 2005. That was the last engine install mod made,
pretty much
       just been flying it ever since, only maintenance now. 660TT,
500SMOH.

       Perry


       Ah Ha so that is where they got it :)


       Paul Lamar ...No rotor no motor.


My memory is slowly coming back. The guy I talked to there at the time
(early 2005) already knew of the concept, and correctly called it a
cross counter flow rad. So I assume they have made them before that time
for other applications.

Perry

Here is a 3D of the cowl with the small spinner Perry.
I guessed the diameter of the spinner at about 10 inches.
Have you considered taping some tufts on the lower back of the cowl and
have a buddy fly along side and take pictures with a telephoto lens.
Perhaps it slopes up  too fast.
A larger spinner would give you more room for starters :) Klaus is
always fooling with the lower part of his cowl cowl back there. It
appears to be a problem area for drag. His latest comes to a narrow
vertical panel.
A slot there would be a good place to dump the hot cooling air.

------------------------------------------

Here is the side view.

------------------------------------

Here it is with less up slope on the bottom. In theory a bit less drag.
The drawback to mounting the rads like this is it precludes laterally
bracing the lower space frame motor mount bay within the bay itself
using diagonals or an X. It becomes necessary to brace the motor mount
laterally with a removable strut over to one side of the spar or the
other.

The previous scheme for mounting the cross counter flow rad would still
work with this cowl.

It quite obvious a rotary mounted in a Long EZ has a lower drag cowl
than a Lyc or Continental. Probably a bit more lift in the bargain as
the wing root is not compromised by the cowl.

Paul Lamar ...No rotor no motor.

Paul
  How far do you have the engine from the firewall?  I think Perry's in
only a couple of inches... I'm trying to snug mine up as close as
possible.  Here are a couple of pictures with the engine positioned...
Still have to figure out what to do with the Turbo and intake... Sticks
up just a little... Also, need to finish the firewall before I weld the
MM braces. I want to ensure there is no interference between the
controls and the MM.

Mike C.

I am going to move it closer.

Are you going to use a jack screw linear actuator as a front strut
mount. Great idea.
I think Burt Rutan would be really interested in this. Imagine a
vectored thrust Long EZ. Should help with takeoff and maybe landing.
Should turn like an F35 :)

--
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net Copyright 1998-2006 All world
wide rights reserved.

Hi Paul
 The design I'm working on is a simple wheel (like a trim wheel) that
is 30:1 geared using a push pull lube to a bell crank.  Trying to keep
it simple.  I'll send some pictures when I get it all working.  There is
some issues with integrating the x-brace as it looks like it will
interfere with the oil pan... So side braces to the spar may be the way
to go.  Sure wish I didn't need them... That would solve a lot of
interference problems when the engine pitches +/- 10 deg.  Can you show
a drawing in Rhino with the Engine pitched +/- 10 deg so I can determine
the minimum distance from the firewall I need to place the engine to
eliminate it hitting the firewall when it pitches?

Mike C.

You will always need a custom oil pan sooner or later :)

Sure I can do that. Maybe not right away as I have some things to order
wile biz is open.
-- 
Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.