Velocity 755V, with its 3-rotor 20B powerplant, has completed 40.2 hours of
flight, and is now released from Phase 1 operating limitations.
No need to clutter the list with congratulatory messages. I appreciate all
the information that has come from this group, and the positive feelings out
there that go with the achievement of this milestone.
Al
Great Al. You would not be planning on going to OSH would you?
Paul Lamar ...No rotor no motor.
---------------
No; not this year. Still have some issues to address - oil temps are
running a bit high in the warm weather; some strange behaviors still with
the EC2; and the RD-1B oil seal in the drive mounting plate has developed
some leakage.
Al
Another old message Al. Paul
-----------------------------------------------------------------------------
-------- Original Message --------
Subject: @#%& Oil leak does Sun & Fun in.
Date: Wed, 05 Apr 2000 17:14:07 -0700
charles harbertwrote:
>
> Ed, sorry to hear you're still leaking. Oil leaks in flight is something I'm
> planning on totally avoiding in the future. The oil pump flow is directly
> proportional to the rpm (positive displacement with pres relief), so the higher
> the rpm the greater the flow. It sounds like your pres relief is set for 80 lbs
> which would be the max flow point. Thus, you need to test at a high enough rpm
> to maintain 80 psi (max pres). There is a significant difference in volume at
> idle pres (20-30 psi) and high rpm which can cause the gbox drain system to
> become overtaxed leading to oil being forced out the gbox rear seal.
>
> This assumes that oil is leaking from the gbox seal, which is the usual place,
> but you'll need to confirm this. I wrote before on this issue, but I would
> suggest you try the following:
>
> 1. As you indicated, test the engine at higher rpm (80 psi) to see if oil is
> leaking by the r.seal. You also should test the oil pressure before the oil
> cooler to be sure it's being relieved properly, and that there's not an
> excessive pres drop across the cooler (assume you 80 psi is after the
> cooler(normal position)).
>
> 2. Consider installing the NAPA scavenge (fuel) pump in a parallel line feeding
> into the pan abv the oil level.
>
> 3. Consider installing a vent line in the gbox (as per latest Ross model), so
> that oil pres cannot build up in the box. Use a clear plastic line to observe
> oil level during test run. You can install this by just drilling and tapping a
> 1/8 or 1/4 NPT pipe fitting into the front gearcase just in front of the flange.
> I'd suggest you do it about the 8 o'clock position. THis line should NOT fill up
> with oil if the drain is working. The only ways to stop this is to restrict the
> inlet flow further(not good), or increase the outflow.
>
> I would bet that the r. seal is still okay, IF you relieve the oil pres in the
> gbox. Did the seal you replaced look distorted? The only reason I think this
> might work is that's the exact problem Dave Atkins and I had 6 months ago. Good
> Luck.
-----------------------------------------------------------
-------- Original Message --------
Subject: @#%& Oil leak does Sun & Fun in.
Date: Wed, 05 Apr 2000 15:50:01 -0700
Ed Anderson wrote:
>
> Hi Folks
> To my great disappointment, it looks like I will not make Sun & Fun. I
> flew a 35 minute test flight after replacing the rear seal in my Ross PSRU
> and moving the oil drain back to the pan down seven inches where it was even
> with the bottom of the Ross PSRU but still above the oil level in the pan.
>
> After approx 20 minutes, I notice streaks of oil flowing up the canopy,
> it did not do that before even when the bottom of the fuselage was covered
> with oil. Sooo, I figured this was a major leak and headed back to the
> airport. Of course, had a nice crosswind and front of canopy was covered
> with oil, but landed without incident. Oil pressure never fluctuated and
> held steady at 80 psi, however, I estimate I lost approx 1 1/2 quarts in
> that 35 minutes, so this is not a tiny leak.
>
> No matter how long I run it up on the ground, I don't seem to leak oil or
> least very little. I have the oil pan vented three places so it would not
> seem that crankcase pressurization would be the problem, but don't know for
> certain. I'll try hooking up a pressure gauge to crankcase, just to check.
>
> I intend to take the prop off and reve the engine to 6000 rpm or so and
> see if I get the heavy leak or not. Needless to say the PSRU will come off
> so I can take a closer look.
>
> My regrets once again not being able to join you all in the fun. Rats!
> Enjoy Sun & Fun and say hello to everyone for me.
>
> Ed
> Ed Anderson
> RV-6A N494BW Rotary Powered
> Matthews NC
I am very disappointed Ed. I was hoping to meet you finally.
Here is a picture of Chuck's scavenge pump. Hope this helps.
This picture was taken last week after Chuck's in flight fire.
If this pump does not work you may have a misalignment in the input shaft
which is causing a wobble at high RPMs.
This oil leak thing with the Ross PSRU is a mystery. If you take your PSRU apart
please take some pictures so I can see what if any changes Ross may have made in
yours.
I assume your PSRU oil supply restriction is 0.030 inch in dia.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.