Subject: PSRU oil leak
From: Rotary Engine
Date: 6/28/2007, 2:55 PM
To: AARotary Engine



           SNIP
           The seal was a National part.  Going from memory, I think the
       p/n was
           3500090, or something similar.  I would have to check on
   that to be
           sure.  It was a nice tight fit.

           Mark St.
           Hi Mark,

           Can you check the seal P/N?  I'm working around a National P/N
       350909
           and before I get too carried away I'd like to make sure I've
   got the
           correct seal. I'm embedding the seal in a new housing "half" to
       control
           the eccentricities better. This will also provide back-up to
   the
       seal so
           internal pressure forces tighter sealing rather than the
   tendency to
           blow the seal out. ( IOW's I'm using housing material to act
       like your
           screwed in retainer ).      Thanx    Dave M

           I would not muck about with cheap shaft seals. I would use
   these.

           Paul Lamar



       Paul,
       Now you tell me!!!  There is no way that I'm pulling that PSRU again
       unless I have to for some other reason.  The seal I used is
   exactly the
       same as what Tracy installed new.  In fact, I took the old plate
   with me
       to get a match on a replacement.  The old one was a different
   make, and
       possibly had a slightly smaller o.d. as it worked its way out of
   the
       hole.  The new one was a nice press fit.  It required a little
       "persuasion" to get properly seated.

       Dave, I'll have to check my receipt tonight and then I can let
   you know
       for sure.

       Mark St.

       Wait awhile. It will leak again :)

       Part of the problem is the current plate and the PSRU are not
   positively
       positioned concentrically using  dowel pins. Universal good
   practice
       for bolted gear boxes, bell housings and rotary engines for that
       matter.
       Larry's bell housing is going to address that problem
       as it will have a machined pilot bore for Tracy's PSRU.

       Furthermore the PSRU bore face will be positively parallel with the
       aft face
       of the engine within half a thou. Currently ANY variation in spacer
       length can
       cause this problem.
       --
       Paul Lamar ...No rotor no motor.


   Paul,

   I believe my name is on the list for a bellhousing.  Until then, I'll
   have to make do with what I have.

   BTW, the holes in my adapter plate were located and bored on a
   Bridgeport with a digital readout.  Locator pins would have been a nice
   addition, but I didn't think of it at the time.

   Mark St.

   If Larry agrees I may have some castings next week. Are you willing
   to mount one, run the 3 rotor engine up to static RPM and have some
   people move
   the tail up and down (with stops of course) to simulate gyro loads?
   One foot high anchor stands for the mains would help for more angle.
   I'll pay for the casting. Larry may donate the machining cost.

   That is all well and good but there are other things that can go
   wrong. Slop in the 10 mmm bolt holes. Bolts that don't protrude
   perpendicular to the end housing. Spacers of varying lengths.
   etc. Did you check the exact position of the 10 mm bolt holes
   relative to the center of the end housing with a DRO?

   If you have a 3" to 4" micrometer measure the exact length of all the
   spacers. Errors can be accumulative in a case like this.
   It is sometimes called a "stack up" of tolerances.

   Paul Lamar ...No rotor no motor.


Paul,
Bob D. did the machine work, and the calculations.  We got the locations
from the drawing on your web site.

I think the recent problem was due to too loose a fit between the hole
and the seal.  It didn't start to leak until the seal worked its way out
of the hole.  I think that was partially due to 100+ psi oil pressure
and possibly an undersized seal and that I didn't use any sealant on the
mating surfaces.  I'm watching the new one closely.  The new seal was a
much tighter fit than the old one.  I'm pretty confident that it will
stay put.

Also, the old seal didn't leak until it moved in the hole.  The sealing
surface is very close to the splines on the input shaft.  When it moved,
the seal was now riding on the edge of the splines, which I feel did
damage to the sealing surface.  Moving it back into place didn't fix the
leak as now the sealing surface was damaged.  The new seal looks like it
will work.  The old seal may have been a cheap Chinese version of what
Tracy uses.  It was green instead of black.  I couldn't read the name as
that is where it was rubbing on the hub.

Mark St.

That dwg may have been inaccurate. I think Larry will probably check
an actual end housing before he machines any bell housings.

People have been having trouble with these seals for ten years.
Not just Tracy's gear box but the Ross too.
The 100 psi rotary oil pressure might have something to do with it.
It could be forcing the seal out of the bore.

Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.