Subject: First batch of 13B Slide Throttles now available. 20Bs on the horizon
From: Rotary Engine
Date: 6/29/2007, 12:12 AM
To: AARotary Engine



    >>> The first production run of slide throttles is complete. I will be
    >>> shipping them out starting next week. As soon as I do, I will
   post some
    >>> pix of them.
    >>>
    >>> The machinist has the drawings for the 20B slide throttles. I
   expect he
    >>> will be making a prototype sometime in the next week or two. Any
    >>> interest?
    >>>
    >>> Doc Custer
    >>> Retired Software Engineer and sometime Audiologist
    >>>
    >>> Here is what it looked like at Sun n Fun.
    >>>
    >>> Paul Lamar ...No rotor no motor.
    >>
    >> Those are the prototypes. The production models are lighter by
   removing
    >> the
    >> rectangular end and making it rounded. Also slightly shorter.
   And the
    >> cover
    >> plates are now 0.125 instead of 0.250, a good saving.
    >>
    >> Anodizing is optional.
    >>
    >> Doc Custer
    >> Retired Software Engineer and sometime Audiologist
    >>
    >> If you don't mind Doc I am going to make a new Teflon
    >> slide and use your housings to test the mech fuel injection
    >> on the p-port RX8 dyno engine. Other than a couple of 1/16th holes
    >> in the spacer nothing else will be modified.
    >>
    >> Paul Lamar
    >
    > OK with me. I have thought some on this. Here are some of my
   thoughts.
    >
    > The Teflon has a much higher coefficient of expansion than AL. I
   found
    > that
    > the Teflon expands 0.02 inches in 2.5" more than the AL when
   heated to
    > 200F.
    > I would recommend that you reduce the width of the slide to
   permit this
    > expansion and install springs between the edge of the slide and
   the inside
    > of the spacer so as to force the slide up against the fuel hole.
   This will
    > allow a better seal between the top of the slide and the point
   where the
    > fuel enters the slide throttle. Of course it would be better to
   enlarge
    > the
    > spacer and covers, but that means a whole new throttle. Maybe you
   can put
    > the springs where they won't interfere with the induction holes.
    >
    > I also used 0.01" total clearance between the slide and covers, i.e.,
    > 0.005
    > on each side. This amount is for heat expansion and the Teflon
   tends to
    > curl
    > slightly and without this clearance the slide tends to be hard to
   move,
    > especially when hot. This gap may not interfere with the sealing
   of the
    > fuel.
    >
    > The Teflon I get varies in thickness from batch to batch, even
   though it
    > is
    > all 3/8" nominally. I specify the clearances and provide the
   Teflon to the
    > machinist, so the spacer thickness varies from batch to batch. I
   think the
    > Teflon in the throttle you have is 0.400" and there is no
   clearance built
    > into the spacer, so Teflon 0.390" would be good, if you can find
   some. I
    > think the side clearance is not critical as long as there is
   enough for a
    > pure throttle. A carb might be different.
    >
    > Incidentally, coarse 3M scotch brite works great for deburring Teflon
    > after
    > machining. It doesn't tend to gouge like a deburing tool.
    >
    > Good luck. I think you will have a difficult time with sealing.
    >
    > Incidentally, my machinist friend needs a carb for his truck. He
   is also
    > thinking of doing what you propose, only with a single hole. I'll
   let you
    > know what he finds out and vise versa.
    >
    > Doc Custer
    > Retired Software Engineer and sometime Audiologist
    >
    > Good advice. Thanks Doc.
    > Well if worse comes to worse and I don't have room for a race track
    > shaped groove and Teflon O-ring around the slot I could go to a
   1/2 inch
    > thick slide. I was thinking of a flat or wave spring, like the
   apex seals,
    > under
    > the Teflon slide.
    >
    > BTW the O-ring groove is not shown yet in these 3D's.
    >
    > Why don't you guys fly cut the Teflon to all the same thickness?
    >
    > Paul Lamar ...No rotor no motor.

   I asked the machinist why he didn't surface mill or grind the Teflon. It
   seems the Teflon "crawls" in the tooling because it is so soft even with
   light cuts. The softness also causes clamping problems. He made a
   special
   "jig" - he called it "tooling" to prevent this effect. The results
   speak for
   themselves - a precision part.

   The art of being a machinist is the shop knowledge of what tooling
   is needed
   to hold the work piece and how to make it if it isn't a stock piece of
   tooling. It is bad news if the work piece shifts in the tooling or
   bows up
   or ... well you get the idea. Especially if it isn't repeatable. Teflon
   crawls erratically. I once had a lathe and a mill and my results
   were circa
   1940, not what I wanted. So I decided I would be a really good software
   engineer and let the guys who know what they are doing be the
   machinists. I
   did like making parts though. I am still tempted to buy another
   lathe ...
   Oh, well.

   The kind of spring I was thinking of is shaped like a recurved bow
   as in
   archery. Put two or three in the bottom and they will force the
   Teflon up to
   help seal the sliding joint.

   I hope the O-ring works. And you have a lot of success. How are you
   going to
   deal with the left over fuel in the system after the engine shuts down?
   Maybe a positive shut off valve right at the slide throttle?

   I know my machinist is interested in the problem. As I mentioned
   previously,
   he plans on making one for his truck instead of buying a new carb.
   Would you
   like to be put in touch with him?

   Doc Custer
   Retired Software Engineer and sometime Audiologist



   There are several ways of machining soft thin material.
   One is a vacuum plate. Another is double back adhesive tape which
   of course will not work with Teflon.

     IMHO a vac plate would work with a couple of large diameter locating
   pins that just fit in the 1.875" diameter holes in the Teflon.
   Tooling :)
   I have a vac pump.


   I had a few problems myself. Here is what I did. Somebody recommended
   Brad point drills. I suspect the shape of the cutting tool has
   a lot to do with it. Larry do you have any ideas on cutting
   Teflon?

   I think I will shut off the fuel pump and let it run out of fuel.

   --
   Paul Lamar ...No rotor no motor.


What's the difference in actuation effort (under load) between a Teflon
slide and some other slick coated material - maybe a coated aluminum slide?


Matt-


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.