> >Can you check the seal P/N? I'm working around a National P/N
> 350909
> >Thanx Dave M
>
> >Dave;
> >National 350909 is correct. My opinion is that it is a
> quality part. I
> >went to NAPA and got another brand on cross reference; the
> National is a
> >better seal. It is wider, and has a good spring to maintain
some
> tension on
> >the seal.
>
> >Al
>
> >Thanx Al, Dave M
>
> >Do you guys have a web address site for National Oil Seals?
>
> >I found this but it is not in the range of numbers above.
>
> >Paul Lamar
>
> Hi Paul, Can't help at all, I've had this seal for quite awhile
> waiting for the day to use it but now that you've asked for
> info.....I
> can't find any! I just tried Google for National
Federal-Mogul oil
> seals and different combos of same. It looks like Timken (the
> bearing
> people) may have bought National but their website is painfully
> slo on
> dialup and showed no cross reference to the 350909 National p/
> n. When I
> went with this seal it stated "made in the USA" which at the
> time the
> McMaster Carr catalog page wasn't telling where their seals
> came from.
> This seemed like an aplication where the USA logo might be
> worth paying
> for. For those following this thread....wrap some cellophane
> tape around
> the spline before you slide the oil seal over it and make
sure you
> install it in the correct orientation (sometimes the obvious is
> not
> always obvious : ) Dave M
>
> What diameter is the shaft?
> --
> Paul Lamar ...No rotor no motor.
>
>
> The 700R4 / 4L60 Transmission had a problem blowing the front
seal
> where the converter neck enters the transmission over the input
> shaft. This was a problem especially when pressure was
> increased as
> part of the aftermarket strengthening of the transmission.
>
> The solution may or may not apply to the current problem.
>
> The oil input was for lubrication of the bushing of the turbine
> shaft neck. The exit (drain) hole was enlarged to relieve the
> built
> up pressure. The seal which is enclosed in a stamped steel
ring
> was coated with red locktite when installed. Finally, a spring
> steel retainer (GM part) is installed over the seal housing.
>
> Joel
I mentioned this before but no response. Why not retain the seal
with keepers. I vaguely recall we went over this a few years ago.
The keeper could be a 360ºcollar or just a couple of tabs. Jerry
That will work.
BTW the seal is definitely marked National S-1621 350909 and
it is one inch ID and 1.5 inch OD and .310 wide.
According to this Timken/National chart standard seals are marginal in this
application at 7000 RPM. Particularly at 220 F which might be a typical temperature
of the gear box case.
The McMaster part number for the high temp. high FPM shaft speed
graphite impregnated Teflon seal is 131295K95. Unfortunately it is only 1.25 inch OD
which is not a problem with the new bell housing but will require an adapter
for Tracy's plate.
SKF part number is 9811. Width is is .375" A bit wider. However it
is Nitrile which is marginal for this app.. Apparently .310 is not a widely
available width. .375 seems to be the standard.
Paul Lamar
Paul,
To verify the p/n seal I recently purchased, it is National p/n 350909.
This number was the same as the one still installed in the original RWS
psru plate.
Mark St.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.