I got the entire overhaul kit from Tracy since he had a 20B kit. I
would
have had to bought 2 13B kits from Mazda to get the everything I
needed. I
actually assumed He had actual Mazda kits. I had no Idea there were any
other options out there. Plus I figured he was the expert on
Mazda/Aircraft
since he does practice what he preaches. He's logged more hours in
Mazda/Aircraft than anyone else I can find, and he runs what he sells.
Bob Mears
I don't think he has Teflon O-rings in any of his engines. I know
he did not have them in the first two engines.
The RX8 engine he is now flying was built around 2004 and at that time
I don't think he or Bruce Turrentine were fans of TES O-rings. Bruce
built his
last two engines. I know his kit was not available at the time his RX8
engine
was built. I doubt seriously he has HIS apex seals or HIS Teflon
O-rings in
his current engine. So much for marketing slogans.
Paul Lamar ...No rotor no motor.
I don't think he has Teflon O-rings in any of his engines. I know
he did not have them in the first two engines.
The RX8 engine he is now flying was built around 2004 and at that time
I don't think he or Bruce Turrentine were fans of TES O-rings. Bruce
built his
last two engines. I know his kit was not available at the time his RX8
engine
was built. I doubt seriously he has HIS apex seals or HIS Teflon
O-rings in
his current engine. So much for marketing slogans.
Paul Lamar ...No rotor no motor.
Paul, I don't know if he has "his" TES O-rings But he probably does
have his apex seals. Bruce was the primary in the design. FWIW
Bill Jepson
With all due respect to Bruce as a vocational high school teacher I think he
is naive when it comes to the history of the apex seal. Bruce was on here
for a very short while but we have been talking about this off and on for
nearly the last ten years.
Some comments from Jeff Spitzer from the Aircraft Rotary Engine Newsletter.
Jeff worked for Paul Moller and his responsibility there was redesigning the one
rotor air cooled OMC rotor engine to a two rotor liquid cooled engine. Jeff
is now the project engineer on the Predator UAV.
-------- Original Message --------
Subject: Home made cast iron tip seals?
Date: Tue, 08 Sep 1998 16:37:29 -0700
Jeff Spitzer wrote:
"Simple cast iron" will probably not make a suitable apex seal. The oil film
between the apex seal and trochoid is practically non-existent. That is why
your quoted text refers to a hardening process for the wear surface.
The apex seals that were in the OMC engines were made from M2 tool steel.
They are fairly expensive to make because they must be ground on three to
five sides (one of them a radius as you mentioned) after heat treat.
Another issue that must be addressed is the combined friction/stiffness
effects at the trochoid boundary. It was found by OMC (which used a sprayed
on carbide trochoid surface) that the heavy steel tip seals were needed to
dampen chatter just after the major axis. Lighter seals seemed
like a good idea until this problem was discovered. If you change materials
(e.g. ceramic, carbon) and reduce the friction then you can reduce mass and
still not experience chatter. My only point here being that it ain't as easy
as "x is better 'cause y" really this is a challenging area to delve into.
Jeff Spitzer
*****************************************************************
Yes, I finally realized that after running across that SAE paper on the
subject.
BTW In rotary drag circles this chatter phenomena is refered to as "jump-off
the hump" :-)
Paul
*****************************************************************
Not actually. If you read again I was talking about just after the *major
axis*. The phenomenon you are referring to occurs at the minor axis and
always gets better with lighter tip seals (for high RPM running)
Jeff Spitzer
*****************************************************************
Mazda claimed they had completely solved that problem back in the early
seventies either with special cast iron apex and Ni and SiC plating or hard
chrome plating and aluminum impregnated carbon apex seals.
Cast iron and tungsten spray coating also works.
Of course what has replaced the carbon aluminum seals for racing now-a-days
is ceramic which works on the stock housing.
I have never seen a rotor housing with chatter marks.
Paul
*****************************************************************
Paul Wrote:
I guess the major axis is where the apex seals change angle from drag to
push.
Is that right?
*****************************************************************
Yes, IIRC this is where the apex seal begins to push. The chatter is caused
by the drag of the tip seal pushing the seal back up into the rotor groove
hence lifting it slightly from the surface. This, of course, reduces the
drag and the seal recontacts the surface. If this phenomenon is resonant you
have excessive chatter. The exact location where this will occur is usually
somewhat after the major axis on the combustion side leading up almost to
the exhaust port. (The intake side has more oil, less drag) The factors that
determine this location are seal angle (push), tip speed, friction, seal
mass, seal spring rate, etc. Note that the seal is slowing down throughout
this region causing a change in the normal force/friction among other
things. This is one of those cases where if everything is just right it will
go wrong :)
Jeff Spitzer
*****************************************************************
So it is real important to match the spring rate of the apex seal with the
weight of the apex seal itself. Two mm cast iron verses three mm cast iron
for one example.
Higher spring stiffness and lower apex seal weight would increase the
resonent frequency of course.
Another good argument for light weight ceramic apex seals.
Paul
*****************************************************************
Jeff Spitzer wrote:
Yes, in general I think lighter seals are better. Don't forget that there
are really two springs here. One is the apex seal spring. The seal spring is
really secondary in importance to the trochoid surface "spring." The
frequency of the spring mass system when just the seal and leaf spring are
considered is probably so low that the seal would be off the housing for a
major part of the cycle for resonance. This just can't happen. That's why I
made the point originally that compatibility of seals and trochoid surfaces
must account for all factors (seal mass, friction, surface "spring rate"
etc).
Jeff Spitzer
*****************************************************************
I don't want to give the impression that this is a major problem.
Nobody has complained in decades. The only problem Abel mentioned with his
700 HP Mazda two rotor is jump off the hump at 10,000 RPM and not chatter.
Paul
*****************************************************************
Jeff Spitzer wrote:
I received a brochure in the mail for a company that does metallurgical
analysis. They are SMTS in Riverside. 909-689-6144. No endorsement.
Jeff Spitzer
*****************************************************************
Funny you should mention that. I just got Hurleys apex seal done at UCLA. 3%
Si, 92% Fe, 1% S, 1% Cu trace elements make up the rest. Don't know the
percentage of carbon yet. Electron microscope. That is Doctor Sergey
Prikhodko with me in front of the EM. Anyone recognize that alloy?
Paul Lamar
End of quote.
-----------------------------------------------------------
I suggest everybody read
http://www.rotaryeng.net/history.html
in its entirety.
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2006 All world wide rights reserved.